How to conduct pre-chamber combustion simulation using ANSYS fluent or Forte?

More Arun Teja Doppalapudi's questions See All

What may be the reasons for failures of Tube toi Tube Sheet Joints in Boiler Drum ?

We have observed that tube to tube sheet joint leaked in our boiler and needs to overcome same by knowing the root cause.

08 August 2024 3,161 0 View

Propose a comprehensive plan to design the new telecommunication system for the company, considering the following aspects:?

a) Design a scalable and robust network architecture that can handle the increasing data traffic and support various communication technologies. b) Recommend suitable transmission technologies,...

10 June 2024 2,187 1 View

How to plot axial ratio for a circular polarizer using hfss?

need details

20 April 2024 4,660 0 View

Need journals on kaolinite clay and biopolymers?

I need more articles on kaolinite clay and the same clay treated by number of geotechnical methods

14 February 2024 607 2 View

Hello all, How to calculate mean gas temperature inside the chamber at different crank angles using pressure data at that particular crank angle?

Pressure data has been recorded at each crank angle in a diesel engine, and I couldn't able to understand how to calculate the temperature from that data. is it possible or any other way to...

24 January 2024 2,926 3 View

The most welcome morning breakfast beverages are tea(black, green, oolong) and coffee(filtered, instant: both dehydrated and liquid). What do yo like?

Dear All, As I mentioned in the question itself these two beverages are saught after worldwide as a refreshing drink. Though, I like both tea and coffee the personal preference on day to day...

02 November 2023 2,011 8 View

On WIEN installation, problem with dstart?

I am new to WIEN and have been reading and looking at youtube installation instructions. However, I have not been able to make a clean installation. Errors start with SCF calculations where dstart...

02 September 2023 9,675 0 View

Purpose of reference electrode and counter electrode in supercapacitor?

22 August 2023 4,341 4 View

Purpose of reference electrode and counter electrode in supercapacitor?

purpose of reference electrode and counter electrode in supercapacitor?

22 August 2023 2,710 3 View

Anyone having issue with derivatization of amino acid using Fmoc?

I have to detect glutamine from a biological sample using HPLC/LC-MS. However, glutamine is very polar and doesn't bind to the column nicely. I used Fmoc to derivatize glutamine so that it can...

10 August 2023 5,839 3 View

Question about combustion Kinetics ?

I am currently working on modeling FCC catalyst regeneration and have come across a point of uncertainty that I hope you can assist me with. In my previous models, I have utilized lumped kinetics...

30 July 2024 6,137 0 View

Problem with Two-phase simulation?

Hello; I am conducting a CFD study on two-phase flow in a separator, utilizing refrigerant as the working fluid. For this study, I have implemented pressure inlet and pressure outlet boundary...

25 July 2024 2,309 5 View

How to introduce on fluent the optical loss of the wall due to the reflection of the plate towards the environment ?

"When solar irradiation reaches a surface, some of it is absorbed while the rest is reflected. Part of the light absorbed by the surface transforms into heat and increases the module's...

13 July 2024 8,621 5 View

How to add a mass source term in the continuity equation?

Hi, I am trying to model laser cladding in Ansys FLUENT. There are two phase: one is base metal surrounded by an inert gas (shown in the image). I want to add a cladding layer of the same metal....

07 July 2024 1,182 8 View

Why i can't get access to isosurface in fluent?

hello everyone i get into fuent and i select the result icone then i try to create an isosurface but the button is gray so i can't choose it. what's the problem? any suggestion.

03 July 2024 5,418 4 View

How to solve the question of ansys fluent?

Regarding the system coupling issue where the update of the solution component fails, the system coupling update for fluid flow (Fluent) triggered an exception: "Update Solution Failed."

30 June 2024 7,894 1 View

How to converge PEMFC in Ansys Fluent?

I am simulating 1 cell of PEM with an area of 50 cm². The mesh has an orthogonality of 0.2 for the channels and bipoar plates (polyhedra) and a quality of 1 for the active zones (hexagonal). The...

26 June 2024 2,358 0 View

Why aren't primary MHD generators with tokamak/stellarator configurations studied/researched?

Magnetohydrodynamic generators are normally used as eihter an attachment to recycle wasted heat and flow of other generators, or used to absorb the energy from rocket thrusters. However, I'm...

24 June 2024 3,949 1 View

What is the exact mathematical formulae and the C++ code of EMMS drag model that is used and applied in ANSYS Fluent 2023?

EMMS - Energy Minimization Multi-Scale

18 June 2024 5,857 2 View

How to compile a udf in Fluent to import hourly weather data and update the boundary condition based on it ?

Hello all, I've compiled a udf which reads velocity data with corresponding time stamp from a .csv file using DEFINE_ON_DEMAND macro. Then, I use DEFINE_PROFILE to define an inlet velocity profile...

14 June 2024 6,480 0 View

Sridhar Sahoo

For Ansys Forte, You may create an assembly design (.xt file) consists of two valves and one main body.

Import the design in Ansys Forte, Further on decomposition, the complete design, integrated for the precombustion chamber will remain further.

Hope it helps..

Oras Khudhayer Obayes

I think below attachment help you