How to coat activated carbon on copper plate?

More Krishna Prasad's questions See All

What is the sample preparation technique for carbon samples?

I have made some carbon samples both CNTs and also activated carbons. How to we get clean SEM images. What is the sample preparation required? What is the sputtering time or cycles to be employed?

08 September 2018 1,461 5 View

Can Lithium metal be used as reference electrode?

Can litium which is very reactive be used as an reference electrode in an electrochemical process. If so how do we use it as a counter and reference electrode. Also handling this setup does it...

06 July 2016 7,128 2 View

Can any one mention reactions which can be monitored by GC?

I would like to monitor ester hydrolysis with GC. can any one help me by pointing out if there are any reactions that can be done so. Thank you.

06 July 2016 9,989 3 View

What are the maximum working potentials for a glassy carbon electrode?

Can GCE be used with a oxidation potential of more than 3V?

09 October 2015 5,385 3 View

How many equivalents of selenium dioxide are required for oxidation?

I am carrying out the oxidation of benzylic methyl group to carbonyls. I wanted to use SeO2 and so wanted to know how many mole equivalents of it is required to oxidise one mole of methyl group....

04 May 2015 2,351 5 View

What is fluorescent quantum yield and how do you calculate it?

What is fluorescent quantum yield and how do you calculate it? Are there many procedures and if there are which one is more accurate?

02 March 2015 4,887 10 View

What is the best procedure to oxidize 2-methylpyridine to the corresponding acid in high yield?

As there are many procrdures...

31 December 2014 2,125 2 View

What is the reason for current dropping in OER , LSV curve?

I tried four trials of the same Copper Phosphides sample in Alkaline medium ( 0.5M KOH) with Hg/HgO reference electrode and Pt as counter electrode. I used 0.001 V/s scan rate for first three...

10 August 2024 3,629 1 View

Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

Do interactions between biosphere, carbon cycle, & water cycle impact global warming & interaction between atmosphere & hydrosphere?

How do interactions between the biosphere, the carbon cycle, and the water cycle impact global warming and interaction between the atmosphere and the hydrosphere?

09 August 2024 3,291 2 View

How do I conformally do PR spin coating on trench structure?

I did PR spin coating on trench structure. I used AZ P4620 PR and the thickness or PR is around 11um. The substrate is Si. And my trench structure depth is 141um(negative way). Even though I...

08 August 2024 2,298 0 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

Who of all of you will help TPEOM to re-originate the Earths atmosphere to it original 5 atmospheric elements/gases?

Global ‘Weather’ has stopped, as ‘aqua thermionic instituted by the ‘Global thermo atmospherics has instituted global thermodynamics of 120º C + and thus all waters are, or have boiled into a...

06 August 2024 8,716 0 View

How can I separate graphene from amorphous carbon of similar particle sizes?

The starting material is a finely ground powder. Some particles contain more graphene than others.

30 July 2024 3,978 2 View

Question about combustion Kinetics ?

I am currently working on modeling FCC catalyst regeneration and have come across a point of uncertainty that I hope you can assist me with. In my previous models, I have utilized lumped kinetics...

30 July 2024 6,137 0 View

What is the reason I get 400nm nanoparticles using an extruder with 200 nm membrane for cell membrane coating?

I am trying to coat my micelles and PLGA based nanoparticles with cell membrane using an Avanti mini extruder according to literature . I use 200nm membrane but my particles end up to be 400nm And...

30 July 2024 3,294 3 View

Addition of EDTA during the synthesis of copper nanoparticles to prevent it from being oxidized?

I've attempted to use this method to synthesize copper nanoparticles. Copper nanoparticles can be synthesised using a variety of precursor materials. CuSO4, distilled water, NaOH, and EDTA are...

28 July 2024 8,027 3 View

Yashwant Pratap Kharwar

You can coat Activated carbon@copper plate using slurry painting method.

Krishna Prasad

what is the binding agent used?

take little amount of sample in pastle mortor and drops of Titan X100 as binding agent and crush to make slurry...

Sorry..........Triton-X100 .........not Titan X100