I am working on a LES case in ANSYS FLUENT. I need to calculate u' i.e. the fluctuating component of the velocity. How to get the data about u' in FLUENT?
I am modelling a flow through porous media using ANSYS Fluent. The flow through porous media is assumed to be laminar. Shall I need to check y+ value in the porous zone also?
08 September 2018 7,873 6 View
I am simulating a pipe flow using water as working fluid under Uniform Heat Flux conditions. The ultimate aim is to calculate Nusselt number in laminar and turbulent regime of the flow. I am not...
03 April 2018 2,272 3 View
I have a FLUENT case of pipe flow. 'X' is the axial direction. I want to plot the vorticity contours in r and \theta plane. How to convert x y and z vorticity to z,theta and r vorticity componenets
07 August 2017 2,681 5 View
Large eddy simulation grid requirement mention about Delta X+ = 100, Delta Z+ = 30 and y+ = 1. Y+ is known but what do you mean by Delta x+ and Delta Z+, x is streamwise and z is spanwise directions,
06 July 2016 6,301 4 View
I am trying to simulate transitional flow in a smooth circular pipe using Ansys FLUENT. Is LES is suitable for transition flow modeling? if yes, which SGS model can capture the transition behaviour?
04 May 2016 9,690 9 View
In SST k omega model the flow is resolved up to the wall. For this the y+ =1. However, in some cases where the solution is converged and showing fairly good results, the y+ values...
01 February 2016 543 13 View
I am trying a case in FLUENT where I need to calculate fluctuating components of the velocity. I RSM model for capturing turbulence. Can you suggest any method to get these components
31 December 2015 6,957 8 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...
29 July 2024 2,032 2 View
Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...
27 July 2024 356 3 View
Hello; I am conducting a CFD study on two-phase flow in a separator, utilizing refrigerant as the working fluid. For this study, I have implemented pressure inlet and pressure outlet boundary...
25 July 2024 2,309 5 View
Hi everyone, I am working on a simulation involving restricted canal with ship using DFBI. I am facing reversed flow in my outlet boundaries as the DFBI is released (In 1.25s). Is there any...
17 July 2024 7,032 1 View
I performed fea on tensile dog bone specimen using ANSYS static structural and also tried using ANSYS explicit dynamics. In experimental result the load is 500 N and deformation is 0.6 mm...
13 July 2024 3,631 4 View
"When solar irradiation reaches a surface, some of it is absorbed while the rest is reflected. Part of the light absorbed by the surface transforms into heat and increases the module's...
13 July 2024 8,621 5 View
I have a 3D output in the figure section of Matlab, does anyone know a way to transfer it to Abaqus or Ansys? Or in what format should I save it so that these analysis software can analyze it?
09 July 2024 9,226 3 View
Hi, I am trying to model laser cladding in Ansys FLUENT. There are two phase: one is base metal surrounded by an inert gas (shown in the image). I want to add a cladding layer of the same metal....
07 July 2024 1,182 8 View
hello everyone i get into fuent and i select the result icone then i try to create an isosurface but the button is gray so i can't choose it. what's the problem? any suggestion.
03 July 2024 5,418 4 View