What is the effect on the conductivity of the thin film during the process of thermal evaporation ?

Why thermally evaporated (VCM 600 V1 configuration of the thermal evaporator) CdTe film found n-type not p-type conductivity whereas all CdTe films deposited by varying the source to substrate...

23 November 2020 7,427 3 View

Can I analyse NGS DATA from an EXCEL spreadsheet?

Hi, I have Fold expression of RNAseq data obtained from Ion Proton sequencer and got the fold change data with mean in an excel sheet. now can I analyse this fold change data using any...

20 October 2020 2,240 3 View

Monolitic construction of brick masonary and concrete simultaniously have any effect ?

Concrete column casting after masonary completed monolithic.

17 August 2020 7,172 3 View

Rentraint Corner of building if need extra stitching diagonal reinforcement ?

If temperature reinforcement already provided ,at reentraint corner need extra diagonal reinforcement ,if needed then what amount of steel.

12 August 2020 1,707 2 View

No title

26 July 2020 1,511 0 View

What is the best management strategy for Diamond Back Moth (DBM) in cole crops?

What should be the best managemnt option for suppressing the DBM problem that farmer can take into consideration?

11 May 2020 4,280 1 View

Is it a good idea to retract a submitted article as the journal is taking too much time to make a decision?

I had submitted a research article related to the field of mechanical engineering (CFD) on the last December, 2019 in a Scopus Indexed journal. It has been around 6 months but the journal...

11 May 2020 9,286 8 View

Where can I get details of SARS-CoV-2 infected patients?

I have been working on peptide vaccine for SARS-CoV-2 or COVID-19 and also recently published some analysis on mutational changes in this virus. It would have been really helpful if I could get...

05 May 2020 2,749 9 View

How does the chemical etching (using HF) affect the temperature sensitivity of a fiber Bragg grating (FBG) inscribed in silica fiber?

Due to chemical etching, the cladding diameter of the silica fibre decreases with time. How does this reduced cladding diameter affect the temperature sensitivity of an FBG, which is inscribed on...

17 April 2020 4,771 2 View

Can anybody help me define the type of isotherm and hysteresis of the three samples?

the attached graph is the isotherm curve of three materials obtained through BET. Also it would be helpful if the nature of porosity of the materials can be commented on. Thank you

04 March 2020 372 4 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Is there any test to determine the cardiovascular risk of patients with obesity? from the perspective of obesity?

We found tests to determine cardiovascular risk taking into account lipid profile, blood pressure, age, history of diabetes, other laboratories. But when weight is involved, there is a paradox. I...

02 March 2021 6,036 1 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

What SPSS analysis should I run with one IV (with two levels) and two DVs?

Hi, I am trying to figure out which test would be most appropriate to run for the following question: Is there a difference in task blood pressure between smokers and non-smokers? There are two...

01 March 2021 8,235 2 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

Issues with Permeabilization during Flow Cytometry?

Hello Everyone. Currently I am working to characterize macrophages in the myocardium after ischemia-reperfusion injury in rats. Due to the low total cell number isolated from rat hearts I can...

01 March 2021 3,867 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View