How to calculate the porosity of PLA implant (FDM printing method)?

21 May 2020 0 9K Report

We push implants from PLA 60% filling by FDM printing method. How to calculate their porosity? Nozzle 0.4 mm. PLA thread thickness 1.75 mm

Badges
Science topic

More Irina Adler's questions See All

How to prevent detection HA-tagged protein after IP if I look for other proteins?

Hello, I do IP using HA-tagged beads. One of my proteins through which I precipitate complex has HA-tag. I see this protein (with HA-tag) after IP. The signal is strong and bright. The complex...

28 March 2024 4,493 2 View

Can I simultaneously measure concentration of cytokines in serum and culture medium with Multiplex Luminex assay?

Dear colleagues, We are planning to use Human XL Cytokine Base kit for evaluation of concentration of several cytokines. The plan was to measure concentration of cytokines both in blood serum, and...

20 February 2024 7,692 0 View

What is the price (average) in USD of Microwave-assisted hydrodistillator with a 1000 mL flask?

I need to buy this equipment to obtain several essential oils.

18 February 2024 401 0 View

Can I perform re-extraction of RNA from eluted RNA (Column filter extraction protocol)?

I encounter the following problem: I want to send viral RNA for further analysis. As the receiver requires, I must process my samples according to a regular RNA extraction protocol and send the...

06 February 2024 7,465 4 View

Development of a smart refrigerator for 1C?

What are the main advantages and potential applications of a smart refrigerator developed on the 1C platform, and what functionality can be implemented using this platform?

29 November 2023 8,294 1 View

Can I use a hot-start polymerase (antibody blocked polymerase activity) for amplification of PCR products before sequencing?

I have the following question: I have a nested PCR protocol that uses a chemically modified hot-start polymerase. However, in the lab, I have a hot-start polymerase, but bounded to an antibody....

16 May 2023 6,906 2 View

Significant overall model in PROCESS SPSS but insignificant predictor effects?

Hello everyone! I have a question regarding results from PROCESS in SPSS. The overall model (model summary) is significant, however, the main effects of the predictors and their interaction are...

22 April 2023 8,485 4 View

Significant overall model in PROCESS SPSS but insignificant predictor effects?

Hello everyone, what does it mean when the overall model (model summary) in PROCESS in SPSS is significant, however all of the effects of the predictors and their interactions are not significant?...

20 April 2023 3,205 5 View

This question was deleted ?

[DELETED]

19 February 2023 7,602 3 View

Have you observed a similar disease Ulmus pumila in your cities and countries and do you have information on the pathogen?

In the city of Dnepr and Dnipropetrovsk region (Ukraine) many damaged trees Ulmus pumila are found in 2021 -2022. Other elm species are not damaged. These are mainly mature trees. Young trees are...

05 February 2023 4,371 4 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Is it necessary to covary exogenous constructs in a structural model?

I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...

03 August 2024 6,028 4 View

Given the current level of natural phenomena cause by the climate change and environmental pollution, will the AI find the technological solutions?

AI-driven technologies offer previously unheard-of capabilities to process enormous volumes of data, extract insightful knowledge and improve predictive models, according to the UN’s World...

31 July 2024 9,733 3 View