How can i predict values of current density along axis in Ansys?

08 September 2019 9,928 4 View

Chemical wear analysis, can be done by ANSYS?

i have block exposure form its surface to liquid with high temperature, this block corroded i want to simulate this wear using finite element this simulation can be done by ANSYS?

06 July 2018 8,801 2 View

Ansys materials properties?

08 September 2016 3,271 2 View

Where i can find the charts of mechanical properties of materials with temperatures?

10 November 2014 8,512 5 View

Why is aluminum not extracted from alumina by pyrometallurgical operations?

.

04 May 2014 1,421 8 View

What is the net and gross anode consumption in aluminum reduction cell?

Aluminum industry.

09 October 2013 9,182 2 View

How two melting peaks in DSC of polypropylene can be merged into one crystallization peak?

The figure shows DSC cooling (blue) and 2nd heating (green) curves (step: 10 K/min) for a commercial sample supplied as Atactic Polypropylene (APP). The heating curve illustrates two major...

03 March 2021 5,857 3 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Precipitate after adding laemmli buffer to protein solution containing Potassium Acetate?

Hi, I am running a size exclusion chromatography experiment with a buffer containing Potassium Acetate as a salt. I analyse these fractions through SDS-PAGE. After boiling my SEC fractions in...

01 March 2021 2,622 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View