Chemical wear analysis, can be done by ANSYS?

More Mahmoud Ahmed's questions See All

How can i predict values of current density along axis in Ansys?

Asalamu alikom I made an electro-thermal analysis using the ِANSYS Workbench of the cathode used in the aluminum reduction cells. What I want to ask is how do I draw a graph like attachment to...

08 September 2019 10,117 4 View

Ansys materials properties?

i am using Ansys in my project but always i have a problem in material properties of my model i want o know the resources of the material properties and the methods to collect it? thank you

08 September 2016 3,379 2 View

How solidification of cast iron can be done by Ansys Fluent?

how solidification of cast iron can be done by Ansys Fluent? and i want to calculate the shrinkage of cast iron after cooling by using fluent

31 December 2015 453 0 View

Where i can find the charts of mechanical properties of materials with temperatures?

i want to find chart of for example poisson,s ratio and young,s modulus vs temperature of aluminum and all other properties of it and other metals thank uou

10 November 2014 8,570 5 View

Why is aluminum not extracted from alumina by pyrometallurgical operations?

04 May 2014 1,530 8 View

What is the net and gross anode consumption in aluminum reduction cell?

Aluminum industry.

09 October 2013 9,241 2 View

Can you connect an HPLC to a Mass Spec only at a certain time point?

Can anyone explain this method? Especially the last statement where it says only at 1.5 to 2.5mins was the MS/MS connected to the UPLC. How is that possible, is it a feature in this specific...

11 August 2024 8,141 3 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How are iso-frequency contours plotted?

Let's say we have a standard, regular hexagonal honeycomb with a 3-arm primitive unit cell (something like the figure attached; the figure is only representative and not drawn to scale). The...

07 August 2024 1,937 1 View

What is the solvent for 8YSZ nano material?

I need to do some experiment with it in liquid form.

07 August 2024 613 3 View

Separation of organic acids-HPLC?

Hello What should be done to separate and identify organic acids in HPC when their RetTime is the same?Like oxalic acid with Propanoic Acid.or acids that have a very close RetTime.

07 August 2024 8,782 3 View

Hi, please what is the best tool on Aspen plus that can help me get the best inlet temperature and pressure for cryogenic distillation?

I am trying to recover liquid CO2 from a mixture of 0.6 CO2, 0.3 N2, and 0.1 O2. My aim is to recover about 99% liquid CO2 at the bottom of the column and make sure the amount of gaseous CO2...

06 August 2024 4,611 0 View

How much Yeast should we add to fermentation media?

I have prepared a liquid broth containing Yeast (S. Cerevisiae) that i need to add from it to fermentation media of lignocellulosic hydrolysate. I need to know based on what parameters do we add...

06 August 2024 662 1 View

RNA later for the preservation of RNA in fecal samples at room temperature for one day (37°C)?

I am planning to collect human fecal samples for metatranscriptomic analysis using MGI. These samples are from indigenous people living in a region with high temperatures. I will have access to a...

06 August 2024 1,367 3 View

How to understand this crystallographic phenomenon of low temperature crystals in zeolite?

During low-temperature testing, new diffraction peaks that appear could be indicative of several phenomena. In one of our tests, we observed notable new peaks around 40° and 45° in a specific...

06 August 2024 726 3 View

Polymer wear calculation?

What is the method for analytically calculating the wear and service life of polymer-polymer sliding pairs?

04 August 2024 1,078 1 View