How magnify colourbar numbers in ansys fluent?

More A. Rezvanivand Fanayi's questions See All

Comment ajouter une recherche ?

En suivant toutes les étapes mentionnées sur (ajouter une recherche) il me signale erreur, ressayer, j'ai essayé plusieurs fois, sans succès, toujours il me signal erreur, ressayer

02 August 2024 9,719 1 View

Why practical assessments of dislocation density by XRD ignores the texture which apparently affects the result?

As one can read in numerous papers on this matter, the dislocation density is derived from the dependence of peak broadening on the diffraction angle, that is, on considered reflections. Thus, to...

28 July 2024 6,496 5 View

Is there any other efficient technique, as an alternative to multiple linear regression ?

with secondary data collected from central bank to know the impact of digitalization in banks profitability, how can its impact be more precisely measured through econometric tools.

21 July 2024 7,295 10 View

Hellow every one i have a question, please help me. How ESP car working?

I try to understand the ESP mechanism working. What kind of sensors it has, Is it necessary to modify or boost its mechanical ?

15 July 2024 4,772 1 View

Are diatom inclusions found in shellfish shells?

Mangroves were reported to eat into limestone atolls like so much cake - but could it have been diatom partnerships at mangrove roots that ate into the rock? If gypsum formation is a clue, how...

12 July 2024 159 2 View

How can I verify if an academic journal is a legitimate publication or a cloned version?

This question seeks to address the growing concern of cloned academic journals, which are fraudulent duplicates of legitimate publications. It aims to guide researchers, scholars, and academics on...

10 July 2024 5,966 2 View

Is there any guidelines about zooming out a chromatogram?

Hi, Just curious to know that in chromatography, a chromatogram should be zoomed to what scale? 10 times of output , 50X or ..? Is there any regulation or general chapter which describes this?...

03 July 2024 3,119 6 View

How to see whether my protein is aggregated using western blotting?

I am working on one protein which gets aggregated (similar to alpha-synuclein and tau) in certain neurodegenerative diseases. I am trying to confirm the aggregation using Western blotting....

30 June 2024 5,060 3 View

Do body proportions of sharks change after drying?

Dear colleagues, I would be grateful to anyone who can answer my two questions: 1. Do the proportions of the shark's body change after drying? In other words, is it possible to discriminate two...

30 June 2024 6,101 3 View

Graphene and graphene oxide as cancer factor?

Please, can any one inform us about risks of graphene and graphene oxide as a factor of cancer growth?

28 June 2024 6,815 4 View

Problem with Two-phase simulation?

Hello; I am conducting a CFD study on two-phase flow in a separator, utilizing refrigerant as the working fluid. For this study, I have implemented pressure inlet and pressure outlet boundary...

25 July 2024 2,309 5 View

How to introduce on fluent the optical loss of the wall due to the reflection of the plate towards the environment ?

"When solar irradiation reaches a surface, some of it is absorbed while the rest is reflected. Part of the light absorbed by the surface transforms into heat and increases the module's...

13 July 2024 8,621 5 View

How to add a mass source term in the continuity equation?

Hi, I am trying to model laser cladding in Ansys FLUENT. There are two phase: one is base metal surrounded by an inert gas (shown in the image). I want to add a cladding layer of the same metal....

07 July 2024 1,182 8 View

Why i can't get access to isosurface in fluent?

hello everyone i get into fuent and i select the result icone then i try to create an isosurface but the button is gray so i can't choose it. what's the problem? any suggestion.

03 July 2024 5,418 4 View

How to solve the question of ansys fluent?

Regarding the system coupling issue where the update of the solution component fails, the system coupling update for fluid flow (Fluent) triggered an exception: "Update Solution Failed."

30 June 2024 7,894 1 View

How to converge PEMFC in Ansys Fluent?

I am simulating 1 cell of PEM with an area of 50 cm². The mesh has an orthogonality of 0.2 for the channels and bipoar plates (polyhedra) and a quality of 1 for the active zones (hexagonal). The...

26 June 2024 2,358 0 View

What is the exact mathematical formulae and the C++ code of EMMS drag model that is used and applied in ANSYS Fluent 2023?

EMMS - Energy Minimization Multi-Scale

18 June 2024 5,857 2 View

How to compile a udf in Fluent to import hourly weather data and update the boundary condition based on it ?

Hello all, I've compiled a udf which reads velocity data with corresponding time stamp from a .csv file using DEFINE_ON_DEMAND macro. Then, I use DEFINE_PROFILE to define an inlet velocity profile...

14 June 2024 6,480 0 View

Fluid flow through copper tube?

What does it mean meshed wall and shell conduction with or without run-out method use to meshing copper tube in Ansys fluent?

07 June 2024 9,030 3 View

How to address gradient discontinuities in CFD - Ansys Fluent?

Assuming I have three domains (three cubes e.g.) placed side by side, the electrical potential equation ( which I am specifying as a User Defined Scalar (UDS)) is solved in the left and right...

05 June 2024 4,153 0 View

Mohammed Ba Zuhair

Perhaps, one way is to reduce the interval between its scale values. For more information see

https://www.eureka.im/952.html

Thomas Frank

Probably the best possible suggestion is, to not to attempt this in Fluent, but to use either CFD-Post or Ensight for postprocessing of Fluent data, since in both that other softwares this is not an issue at all.

Mohammadmahdi Seifi

The best way is that in CFD-Post under "Appearance" of color bar, change the "Text Height".