This question is related to geomechanical constitutive modeling in software Abaqus.
If I want to increase the photocatalytic activity of a thin film sample what should be it's ideal surface morphology and parameters? All scientific answers related this are highly appreciated.
19 June 2024 6,744 0 View
If I want to improve the photocatalytic activity of Ni doped ZnO thin film then which would be the better deposition process for thin film Spin Coating or Dip Coating?
18 June 2024 7,678 2 View
If I want to enhance the photocatalytic activity of Ni doped ZnO thin film. For this what are the parameters I need to tune and how? Related this all scientific answers/explanations are highly...
16 June 2024 4,533 1 View
If I want to check photocatalytic activity, is there any specific reason to choose Nickel doped ZnO thin film sample over Nickel doped ZnO powder sample? How thin film can play role for...
27 March 2024 2,668 1 View
In Lumerical Charge module, metal can only be simulated in case of contact layer as any metal structure always need to be associated with a predefined bias value. Thus, metal nanoparticle embedded...
21 November 2023 8,384 0 View
citation needed
23 March 2023 661 11 View
Kindly tell the electrolytic polishing reagent as well as chemical and electrolytic etchant for 304H austenitic steel.
19 March 2023 8,528 2 View
The membership function can easily be determined depending upon the number of point of scales. But how the non-membership function can be determined for those membership function for triangular...
14 March 2023 794 0 View
I want to do carbonization on SnO2 particle at 500 degree Celsius in Argon atmosphere. Which kind of box furnace is needed there? Valuable suggestions are welcome!
17 October 2022 5,755 1 View
I synthesized 6H-SiC (bulk) pellet and took temperature dependent Raman measurement of that. Now I want to take temperature dependent Raman measurement of pellet of nanocomposite of Epitaxial...
05 March 2022 9,081 2 View
I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?
11 August 2024 3,115 1 View
I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...
10 August 2024 4,005 2 View
Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...
09 August 2024 7,892 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...
08 August 2024 4,831 4 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,028 0 View
Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...
06 August 2024 9,986 2 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View
I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...
05 August 2024 3,665 0 View