What kind of surface morphology must be there for good photocatalytic activity of thin film?

20 June 2024 0 7K Report

If I want to increase the photocatalytic activity of a thin film sample what should be it's ideal surface morphology and parameters? All scientific answers related this are highly appreciated.

Badges
Science topic

Similar topics
Papers

More Arpan Ghosh's questions See All

Is this a facetotecta nauplius?

This larva was captured using a plankton net in the Persian Gulf during the summer. I believe it may be a Facetotecta nauplius.

08 August 2024 3,746 4 View

Z-average size from Dynamic Light scattering can it be lower than the original probe size?

Hi everyone, Recently I have been conducting Dynamic Light scattering experiments in a micellar solution at 5 and gel at 37 degrees of Celsius with latex particles of diameter 190-500 nm. While...

01 August 2024 1,168 4 View

GSH estimation assay: What is the right choice of standard?

Hi there, My question is: What standard curves should be used while estimating Tot GSH and GSSG by kinetic method using GR enzyme mediated recyling with DTNB chromophore? Actually I am following...

01 August 2024 8,217 1 View

Following click reaction in cell lysates, protein is immobile and remains at the top of the gel in SDS-PAGE?

I am using CuBr/THPTA for a click reaction in total cell lysates. I am facing issues with my protein sample in non-reducing SDS-PAGE where it's not migrating properly and most of it remains at the...

29 July 2024 950 4 View

Which filtration method to go for run off water from dirty solar panels to be used again?

We are working on a robot that cleans solar panels using fresh water supply and a rotating brush. We are trying to conserve as much water at possible by recycling the dirty water that is collected...

28 July 2024 5,778 2 View

When making abraxane with Nab tech, why is 9:1 Chloroform&EtOH used as solvents?

Is it the best optimization ratio based on experiments?

22 July 2024 8,170 0 View

Can diamond be grown using molecular beam epitaxy?

22 July 2024 9,755 2 View

Intracerebroventricular (ICV) AAV inj.?

I'd like to know if anyone has got experience in intracerebroventricular (ICV) AAV inj. I am looking for a concomitant spread of the AAV including but not limited to the motor cortex and the...

12 July 2024 781 0 View

How can I use LabVIEW to control of an ethernet-based driver?

Hello everyone, I am new to LabVIEW, right now we need to control the movement of an ethernet-based stage drive. We got the sample code from a collaborator but their instrument is USB-based, so we...

11 July 2024 5,385 2 View

Systematic review meta-analysis paper?

Hi everybody, We are trying to write a systematic review meta-analysis paper. But I could find 19 references. I think 19 references are not enough to do a meta-analysis section and it is better to...

10 July 2024 5,490 5 View

Which type of compound does lamda max of 218 indicate in a uv-vis spectrum of a partially purified compound through column and TLC?

A crude extract of fungal culture using EtOH was subjected to column and TLC and partially purified compound was obtained. UV vis spectrum of the compound/s has max absorbance at 218nm. The...

11 August 2024 9,801 2 View

How can I measure the thickness of thin film by Uv-Vis?

06 August 2024 7,810 3 View

Why is TLC not a form of partition chromatography?

Why is TLC not a form of partition chromatography and paper chromatography not a form of absorption chromatography?

03 August 2024 7,035 3 View

Is there a good freeware software for photodocumentation of TLC?

I need something like Camag's VisionCat software for photodocumentation of TLCs. Could you recommend something?

31 July 2024 8,415 1 View

How to build my own lab made four point probe set up?

Hello, I'm trying to measure the conductivity of semiconductor films but since I don't have a commercial four point probe set up I would like to build one on my own in my lab. I have generators,...

30 July 2024 906 2 View

Can I proceed with Response Surface Methodology (RSM) with only one factor for further optimization?

I went for Plackett Burman Design for selecting the optimization factors of growth conditions for pesticide degradation. I started with 7 parameters. But, after the experiments and analysis, only...

29 July 2024 5,015 1 View

I did hirshfeld surface analysis for molecule but did not find red spot and interaction surface in energy frame work, is it ok for research article ?

In hirshfeld surface calculation i did not find any red spot in hirshfeld surface, is it ok for research article to write?

28 July 2024 2,988 0 View

Does anybody know why my chitosan/pva/gelatin hydrogel dissolve in PBS?

My final research is about making chitosan/pva hydrogel for wound healing using gelatin as crosslinker. Last month, i made the thin film hydrogel and it turn well. It was okay. Last week, i make...

28 July 2024 2,794 6 View

Why specific capacitance is not proportional with the specific surface area?

Dear researchers, Why specific capacitance is not proportional to the specific surface area? I have material A with a surface area higher than material B, but material B is showing little bit...

26 July 2024 9,156 2 View

Is it possible to manufacture polypropylene sheets using a biaxial process?

I know that films and other low-thickness laminated products are produced using biaxial orientation, but is there something similar for sheets with a thickness of around 6 mm? Or are they...

21 July 2024 1,559 1 View