Develop operating envelope?

how do you develop an operating envelope for a solar compressor? what data I need and how do I know the operating envelope would be "perfect"? I have never done anything on operating envelope,...

04 May 2017 6,439 1 View

How do you reflect on a book?

how do you reflect on a book? I usually just close the book and give some thoughts to it but i feel like its not effective way to reflect by just giving thoughts. What are your suggestions? How do...

07 August 2016 9,145 4 View

Can I thank the people who have helped and gave me answers to my questions?

I would like to say thank you to all of you who have helped me so far with my thesis on the movement and concentration of suspended particles in the nodal planes of an ultrasonic standing wave...

05 June 2016 8,723 1 View

How do I get an 80 mark and above on writing a dissertation/thesis project?

I have finished my literature review and I have finished the draft of my numerical simulation(or you could say my own project). What is left is to 'beautify' my dissertation more. How do I get a...

04 May 2016 3,510 2 View

Why are the particles concentrated in the nodal planes for only a period of time?

As you can see from the attached diagram, the particles are concentrated in the nodal planes at 0.008 s. But at 0.1s, the particles are not as concentrated in the nodal planes as at 0.008 s ( i.e....

03 April 2016 4,445 9 View

Look into my acoustic pressure field, does it look like having an acoustic streaming?

Why is it that in the middle there are no standing wave field?How will the particles move when the standing wave field is only on the upper and lower of the cavity?

03 April 2016 4,683 5 View

How much nitrogen is required for regenerating a vapour phased carbon bed adsorption?

03 April 2016 4,821 3 View

What can you deduce from my 1D plot graph of the mass fraction of suspended particles in a standing wave field?

The y-axis shows the mass fraction of the suspended particles and the x-axis shows the length of the cavity. When x = 0, that is to the left end wall of the cavity, when x = 21, that is at the...

03 April 2016 7,848 2 View

For the COMSOL simulation of particle manipulation using ultrasonic standing wave, why is the resonant freq. different at different mesh sizes?

03 April 2016 4,588 3 View

Why are my 1D and 2D plot results look different [COMSOL, ultrasonic standing wave on suspended particles]?

03 April 2016 9,032 2 View

Is there any tutorial for comsol general projections?

Hi, im trying to make a projection in a 3d comsol model. I have a non uniforme chanel and my intention is to get the average tempreture in the y-z cross section and se the average tempreture...

02 March 2021 4,624 4 View

Is it possible to do piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch?

How to do Piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch? Piezoelectric coupling between the rectangular substrate and rectangular...

02 March 2021 9,833 3 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

Can polymer concentrations be calculated based on the number average molecular weight?

Hello, I spin-cast two different polymers onto wafers and measure their height as a function of initial concentration. For polymer A, I have the weight-average molecular weight (Mw) as well as...

28 February 2021 7,882 2 View

RIA. How to measure?

When you use RIA, with a control the unknown sample with antibodies, you bare in mind the binding sites of the antibodies. However you still need to measure labelled antigen (radioactive) and not...

28 February 2021 2,133 3 View

How to Eliminate cosine error and abbe error in LASER measurement system(for example Rhenishaw XL80)?

I like to do project in laser measurement system. My objective is to eliminate or reduce the cosine error, abbe error in Laser measurement system. I have Rhenishaw XL80 system. Please tell the...

28 February 2021 4,890 3 View

How to use measure capacitance change in COMSOL time dependent study ?

I want to measure change of capacitance due to relative displacement between two parallel plates in COMSOL. Distance between two plates changes with time. So I'm using a time dependent study but...

26 February 2021 8,567 3 View

How to measure angle between laser travel path and machine axis in Laser Measurement system?

25 February 2021 1,987 3 View

Error in comsol?

Dear respected researchers, while performing CFD analysis in Comsol it's showing like this Error: Nonlinear solver did not converge. The maximum number of Newton iterations reached can...

24 February 2021 249 3 View

What software programs can directly simulate Additive Manufacturing Directed Energy Deposition (DED)?

I understand there are a lot of software programs that can simulate DED by going through specific modeling, simulation, and commands. For me, that was time consuming and results were not accurate....

24 February 2021 4,428 3 View