How do you calculate the volume fraction of the injection phase in ANSYS Fluent with Discrete Phase Model?

09 March 2015 1 712 Report

I need simulate oil flow injected to a cavity full of air. Because the volume fraction of the oil in the cavity is less than 10%, I want to use the discrete phase model in Fluent. But I don't know how I can get the actual volume fraction of the oil in the cavity.

Mas Fawzi Mohd Ali

Use a multiphase model

Badges
Science topic

More Gao Wenjun's questions See All

How would I calculated ddPCR spiked nucleic acid recovery calculations?

Hello everyone, I'm in the initial stages of conducting a study involving the ddPCR (Bio-Rad QX200, QX600) and I ran into some problems involving recovery % calculations using direct...

02 July 2024 6,011 2 View

Does the zirconium isotope fractionate as through the column?

Is the zirconium isotope of geological sample fractionated when passing through the column, and how to determine whether this fractionation is or not？

26 May 2024 6,721 2 View

In C++, why is the constructor of a virtual base class called first, while the object of the virtual base class is placed last?

In C++, why is the constructor of a virtual base class called first, while the object of the virtual base class is placed last? What are the advantages of doing this?

07 May 2024 1,583 1 View

Through what theories can we aptly explain the social networks and subcultures that people form around cats?

Just like the stray cat protection organizations on campus, they are spontaneous and not organized by the school. They provide a series of services for kittens in life and death. And the source of...

11 April 2024 4,944 0 View

PMSCV for protein transit protein expression?

We are using pMSCV for transit expression of a protein.: 1. The gene was cloned in (between XhoI/EcoRI). 2. Transfection with lipofectmin 3000 to 293t cell. 3. After 48 hrs, GFP can be...

04 April 2024 8,350 4 View

What is the bubble in the cytoplasm?

What is the bubble in the cytoplasm as the figure I attached below? It also can be released into the culture medium after the cell dead.

18 March 2024 1,410 0 View

How to download the protein sequences included in the CAZy databases?

In the latest CAZy sequence list (http://www.cazy.org/), over 3,600,000 sequecnes have NCBI accession and they can be easily accessed. However, the remaining 550,000 sequences only have a jgi...

13 March 2024 2,439 1 View

Who want to publish papers to Scopus journal?

Computer Systems Science and Engineering ISSN:0267-6192(print) Publish within 4 months Low APC: 600 USD(Review paper full waiver) Send me DM for more info

31 January 2024 5,463 1 View

How to calculate the localization length in 1d optical random system?

In 1D random strustures, the Anderson localization is an important phonomenon. Localization length is a key parameter to show the localization characteristic. How to calculate the localization...

28 December 2023 3,999 1 View

How to program spatially correlated Rician fading channels in the RIS enhanced MIMO networks with Matlab?

Hi! I have questions to consult with scholars. We consider a multiuser MISO downlink communication system where an IRS equipped with a UPA ( with M reflecting elements) is deployed to enhance the...

08 December 2023 6,883 4 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

Tangential stiffness option in ansys workbench?

I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...

29 July 2024 2,032 2 View

How to Import Blade geometry from CAD file in ANSYS design modeler?

Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...

27 July 2024 356 3 View

Problem with Two-phase simulation?

Hello; I am conducting a CFD study on two-phase flow in a separator, utilizing refrigerant as the working fluid. For this study, I have implemented pressure inlet and pressure outlet boundary...

25 July 2024 2,309 5 View

Why my simulation results are showing too much deformation compared to experimental result?

I performed fea on tensile dog bone specimen using ANSYS static structural and also tried using ANSYS explicit dynamics. In experimental result the load is 500 N and deformation is 0.6 mm...

13 July 2024 3,631 4 View

How to introduce on fluent the optical loss of the wall due to the reflection of the plate towards the environment ?

"When solar irradiation reaches a surface, some of it is absorbed while the rest is reflected. Part of the light absorbed by the surface transforms into heat and increases the module's...

13 July 2024 8,621 5 View

Can I transfer the 3D file from Matlab to Ansys or Abaqus?

I have a 3D output in the figure section of Matlab, does anyone know a way to transfer it to Abaqus or Ansys? Or in what format should I save it so that these analysis software can analyze it?

09 July 2024 9,226 3 View

How to add a mass source term in the continuity equation?

Hi, I am trying to model laser cladding in Ansys FLUENT. There are two phase: one is base metal surrounded by an inert gas (shown in the image). I want to add a cladding layer of the same metal....

07 July 2024 1,182 8 View

Why i can't get access to isosurface in fluent?

hello everyone i get into fuent and i select the result icone then i try to create an isosurface but the button is gray so i can't choose it. what's the problem? any suggestion.

03 July 2024 5,418 4 View

How to solve the question of ansys fluent?

Regarding the system coupling issue where the update of the solution component fails, the system coupling update for fluid flow (Fluent) triggered an exception: "Update Solution Failed."

30 June 2024 7,894 1 View