How could we reduce NOx release problem from catalyst slurry during preheating and calcination steps?

More Alireza Hadi's questions See All

Question about MHB (Mycorrhiza Helper Bacteria) isolation technique??

What are the most effective isolation techniques for obtaining MHB?? Is there are best approach techniques? I keep struggling in obtaining it.

26 July 2024 7,387 0 View

Question about Single Strain Arbuscular Mycorrhiza Fungi??

Now i am working on AM fungi single strain. What are the most effective isolation techniques for obtaining pure cultures of arbuscular mycorrhizal (AM) fungi?? Is there are best approach...

26 July 2024 6,520 1 View

Can a private laptop with 16GB RAM and Intel i5-1235U 1.3 GHz processor be used for WRF simulation with a 12*12 km domain?

I want to simulate WRF for a 12*12 km domain size. I want to run LSM and BSM models with a 5 minutes time interval. My laptop specification is 16GB RAM and Intel i5-1235U 1.3 GHz processor. Can I...

13 July 2024 2,037 0 View

What do you know about classroom management?

Hello, if possible, please send me new methods of management and communication in the classroom. thank you؟

18 June 2024 4,139 3 View

How do we measure the electrical conductivity of this magnetic nanocomposite?

A magnetic nanocomposite has been synthesized and its electrical conductivity needs to be measured. What analysis and technique can be used to measure the electrical conductivity of this magnetic...

16 June 2024 7,488 3 View

How can I define the failure of the beam connector as a discrete fastener?

I am using the discrete fastener method for an LSF frame, and I want to consider the shear failure of rivets in my simulation. However, when I define lower and upper bounds for shear force, Abaqus...

06 June 2024 9,241 0 View

Is it possible to estimate Horizontal in-situ stresses' directions and magnitudes from seismic data by using AI methods?

We know that one of the important members of a 3D Geomechanical Model is in-situ stresses' directions and magnitudes. we can use the seismic data to estimate these parameters in special record...

21 May 2024 1,332 2 View

Hello. why do we measure surface tension?

surface tension

20 May 2024 4,895 1 View

What are the S-scheme and Z-scheme heterojunctions in photocatalytic systems? for the types of heterogeneous photocatalysts, how can you determine?

what are the S-scheme and Z-scheme heterojunctions in photocatalytic systems? and for the types of heterogeneous photocatalysts, how can you determine the type of S-scheme and Z-scheme?

16 May 2024 1,545 1 View

Why is my first article being rejected fast by related journals?

Hello everyone, I hope you are all doing well. I have already checked plagiarism, related articles’ structures, and grammar, and they seem fine, but good impact factor journals that I have written...

15 May 2024 1,007 4 View

Separation of organic acids-HPLC?

Hello What should be done to separate and identify organic acids in HPC when their RetTime is the same?Like oxalic acid with Propanoic Acid.or acids that have a very close RetTime.

07 August 2024 8,782 3 View

The aqueous fraction of the hydroethanolic extract is showing the presence of palmitic acid. What is the mechanism responsible ?

Palmitic acid presence in aqueous fraction

05 August 2024 8,624 4 View

Need heterogeneous catalysts calcined before reduction?

Metal-containing heterogeneous catalysts often need to be calcined before reduction, so what are some examples of catalysts that perform better without calcination? What is the reason and how many...

05 August 2024 909 2 View

How to convert g/kg Humic acid dose to kg/ha?

I used humic acid at 0.044 g/kg soil in my pot experiment. But finally, I have to recommend kg/ha. Each pot's soil weight was 11 kg. What is the solution?

02 August 2024 7,186 6 View

Is the black sediment consider as sand? If not, how can I filter it out?

Hi researchers! I'm working on soil texture analysis, and the end result for sand is doubtful because there is black sediment appearing after drying, as shown in the figure. Is it considered sand?...

30 July 2024 557 2 View

Inquiry on Maximum Nucleic Acid Volume for 2.5 mL Liposome Solution?

I am currently working on a project involving liposomes and need to determine the maximum volume of siRNA that can be added to a 2.5 mL liposome solution with a total lipid concentration of 10...

30 July 2024 6,420 1 View

Where to start the Analytical model for Dry sliding wear of metal surface ?

I am doing research on wear mechanism of the additive manufactured metal parts under dry condition. Please share the reference to start the analytical modelling of the wear prediction.

29 July 2024 6,115 0 View

I have calcined my catalysts without flowing air from the compressed air cylinder will there be any problem with my reaction if i use that catalysts?

FYI Catalyst is MFI zeolite Si/Al = 140,25.40.11.5,15 I am using this catalyst to study methanol to DME conversion

25 July 2024 2,486 2 View

Why is trifluoroacetic acid (TFA) used in c-18 column?

I would like to know the role of the TFA (trifluoroacetic acid) used on reverse phase chromatography c-18 column. It's is often used with a concentration of 0.1% on the mobile phase.

23 July 2024 8,075 3 View

Can we add calcium carbonate to any media as an indicator for lactic acid producing bacteria?

As mentioned in literature the addition of CaCO3 to MRS Agar media is considered as an indicator for lactic acid producing bacteria, so I wonder if we can add CaCO3 calcium carbonate to any other...

20 July 2024 7,504 0 View

Hermann Ehwald

Could You, please, describe your catalyst and the preparing process more detailed?

Alireza Hadi

Thanks Hermann, This is a three-way catalyst converter and the preparation method is making slurry and wet impregnation.

Without the exact composition of the slurry, the carrier used and the treatment conditions nobody can give You the information You are asking for.