I am using the discrete fastener method for an LSF frame, and I want to consider the shear failure of rivets in my simulation. However, when I define lower and upper bounds for shear force, Abaqus releases the elements from the first increments.
What are the most effective isolation techniques for obtaining MHB?? Is there are best approach techniques? I keep struggling in obtaining it.
26 July 2024 7,387 0 View
Now i am working on AM fungi single strain. What are the most effective isolation techniques for obtaining pure cultures of arbuscular mycorrhizal (AM) fungi?? Is there are best approach...
26 July 2024 6,520 1 View
I want to simulate WRF for a 12*12 km domain size. I want to run LSM and BSM models with a 5 minutes time interval. My laptop specification is 16GB RAM and Intel i5-1235U 1.3 GHz processor. Can I...
13 July 2024 2,037 0 View
How can prepare Alginate Gelatin Chitosan hydrogel?
05 May 2024 6,229 2 View
Hello dears I want to import an LSF model from Tekla to Abaqus. Which type of file should the Tekla model be exported as?
30 April 2024 7,978 2 View
Does Gibbs 2 take into account both lattice and electronic contributions to the specific heat Cp ?
23 April 2024 2,280 0 View
Hi everyone, I'm conducting research on the impact of AI on workforce displacement in the logistics industry for my Bachelor's thesis. If you work in logistics and have experience with AI...
07 April 2024 4,394 1 View
Hi everyone, Hope you are all in good well and health. I am currently pursuing my degree in Bachelor of Science in Logistics. I am searching for reliable survey questions that I can use in my...
01 April 2024 2,499 2 View
Hello, Which are some AI tools that researchers can use in writing scientific paper?
23 February 2024 1,792 4 View
I have recently published a research paper about this actuator and I want know your idea about practical uses of this new actuator.
22 February 2024 10,071 0 View
We have observed that tube to tube sheet joint leaked in our boiler and needs to overcome same by knowing the root cause.
08 August 2024 3,161 0 View
I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...
08 August 2024 4,831 4 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,028 0 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View
Hello, colleagues. Recently, I have been working on a metal processing simulation with my UMAT in Abaqus. I have outlined the corresponding simulation, but I keep encountering issues that cause...
30 July 2024 7,062 1 View
I am trying to run a restart analysis, which imports deformed configurations of parts from a generated ODB file. It runs fine in Windows OS but when I try to run it in Linux OS, it is giving some...
29 July 2024 9,572 3 View
Sure, here is the translation: I have a 3D orthogonal woven composite structure where warp, weft, and binder yarns are oriented in three directions. After modeling these yarns and the matrix in...
28 July 2024 8,169 0 View
hi, I am doing a risk analysis of a cylindrical fuselage with windows. I have applied contact interactions between the different parts, and I have applied a unit value load to a reference point,...
20 July 2024 647 2 View
Hi all, I am using the element deletion process based on a Tsai-Wu criterion through a UMAT with a specific State Value controlling the process (DepVar -> Variable number controlling element...
17 July 2024 1,501 1 View
I saw a paper(PHAN V-T, ZHANG X, LI Y, et al. Microscale modeling of creep deformation and rupture in Nickel-based superalloy IN 617 at high temperature [J]. Mechanics of Materials, 2017, 114:...
16 July 2024 8,436 0 View