How can we make a part(with a new mesh) from an orphan mesh geometry?

01 March 2022 1 5K Report

I have an input file that makes an orphan mesh geometry in Abaqus and I want to convert it into a part to change its mesh.

How can we convert it to a part with a new mesh?

Amer Alomarah

Dear Parmida Rasouli Please see the below YOUTUB videos that explain how to convert an orphan mesh into a part in ABAQUS CAE

https://www.youtube.com/watch?v=zF8Z9J1t50E

https://www.youtube.com/watch?v=y5U_Xa_yMlQ

also double this discussion on research gate

https://www.researchgate.net/post/how_can_i_do_orphan_mesh_feature_in_part_in_abaqus#:~:text=In%20order%20to%20convert%20an,importing%20it%20again%20to%20Abaqus.

Regards,

Badges
Science topic

More Parmida Rasouli's questions See All

How to synthesis the uniform polyamide active layer on the aminated PVC support layer?

we work on forward osmosis membrane. the support layer is aminated PVC and the active layer is polyamide. for synthesis of polyamide , I follow the routine methods of interfacial polymerization...

19 April 2024 3,574 1 View

Method of measuring sulfur for molybdenum oxide?

What is the method of measuring sulfur for minerals such as metal oxide or molybdenum oxide through Leco furnace (or similar furnaces) at different temperatures, times and weights after leaching...

11 November 2023 3,345 2 View

What is ECMWF forecast steps?

Hello everyone, I hope you're doing well! I'm currently looking to utilize ECMWF forecasts for my work, but I've encountered a challenge in understanding the specific steps involved. I've checked...

08 November 2023 3,698 0 View

How to synthesis of SBF (simulated body fluid) for bioactivity tests ?

Every solution I synthesize has a high pH = 8 or above. (I had synthesized my solution by Bohner protocol) What are your recommendations to fix this problem?

17 February 2023 4,046 1 View

As a supervisor, what do you find to be the most challenging problem posed by students on your team?

As a supervisor, what do you find to be the most challenging problem posed by students on your team? Please choose one of the following options. If you have other suggestions, you are highly...

03 March 2022 7,143 5 View

How can we convert an stl file format into a solid part for complex geometries?

Actually, I have tried some methods in CATIA, but it couldn't be readable for Abaqus afterward as it was not a clean geometry.

28 February 2022 5,456 3 View

What is the best mesh size and type for topology optimization? Can we use Adaptive-remeshing before topology optimization?

Is it advised to use Adaptive-remeshing before topology optimization process? (because sensitive sections on my part (which gain the smallest size of the mesh), are actually frozen in the topology...

02 February 2022 4,870 5 View

From which company can I purchase echinocandins disk and powder?

For antifungal susceptibility tests, from which company do you usually purchase echinocandins disk and powder?

26 January 2022 9,148 0 View

Copper Cyanide analysis by AA?

Hello, For a research project, we are analyzing copper cyanide samples using both AA and ICP. The results obtained by AA , for all samples are higher than the ICP readings. Anyone had a similar...

31 May 2021 5,288 5 View

How to model Newtonian fluids flows in a cylindrical stirred vessel?

ANSYS Fluent provides some options for modeling Newtonian flows. Which model can be the best model to simulation Newtonian fluids flows in a cylindrical stirred vessel? And how about the Newtonian...

04 March 2020 2,875 3 View

How to get moment output in Abaqus Standart?

I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...

08 August 2024 4,831 4 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

Simulation of metal drawing by Abaqus with UMAT?

Hello, colleagues. Recently, I have been working on a metal processing simulation with my UMAT in Abaqus. I have outlined the corresponding simulation, but I keep encountering issues that cause...

30 July 2024 7,062 1 View

Why running a restart analysis in Abaqus in Ubuntu OS gives an error as attached when running the same job in Windows doesn't give any error and runs?

I am trying to run a restart analysis, which imports deformed configurations of parts from a generated ODB file. It runs fine in Windows OS but when I try to run it in Linux OS, it is giving some...

29 July 2024 9,572 3 View

How Can I Apply Hashin Damage Properties to Solid Elements in Abaqus Without Using VUMAT?

Sure, here is the translation: I have a 3D orthogonal woven composite structure where warp, weft, and binder yarns are oriented in three directions. After modeling these yarns and the matrix in...

28 July 2024 8,169 0 View

Abaqus cylinder buckling riks analysis?

hi, I am doing a risk analysis of a cylindrical fuselage with windows. I have applied contact interactions between the different parts, and I have applied a unit value load to a reference point,...

20 July 2024 647 2 View

Abaqus 2023 - How to know how many elements have been deleted during a simulation ?

Hi all, I am using the element deletion process based on a Tsai-Wu criterion through a UMAT with a specific State Value controlling the process (DepVar -> Variable number controlling element...

17 July 2024 1,501 1 View

How to cacualte the creep life of polycrystal with CPFEM?

I saw a paper(PHAN V-T, ZHANG X, LI Y, et al. Microscale modeling of creep deformation and rupture in Nickel-based superalloy IN 617 at high temperature [J]. Mechanics of Materials, 2017, 114:...

16 July 2024 8,436 0 View

Hello, does anyone know how I can get coordinates of two specific points on a moving body in Abaqus when applying a vdload subroutine?

Hello I am trying to simulate repulsive force of two permanent magnets in Abaqus. I have implemented Force equations into a vdload subroutine. sensitive parameters are the center to center...

15 July 2024 3,491 0 View