How to model Newtonian fluids flows in a cylindrical stirred vessel?

ANSYS Fluent provides some options for modeling Newtonian flows. Which model can be the best model to simulation Newtonian fluids flows in a cylindrical stirred vessel? And how about the Newtonian...

04 March 2020 2,709 3 View

How to conductive polyethersulfone membrane?

Please suggest a way to conduct low voltage poly ether sulfon membrane.

24 December 2019 5,108 3 View

What would be the best way to characterize a superhydrophobic-superoleophilic satinless steel mesh coated by alkyltrialkoxysilane (DYNASYLAN F8261)?

I already utilized XRD and FTIR tests, but the quality of peaks is not good enough to interpret. Apparently, XRD is not suitable for organic materials. So, what is the best way for analyzing these...

12 November 2019 9,221 4 View

Does any one know why in an LDH with M-N-X chemical formula, the M2+ and N3+ ions dissolve differently in aging condition? L/S and pH effect?

during aging of my LDH material, Ca and Al ions dissolve with different proportions in aging process. At pH 8, L/S 20 Ca dissolves more than Al. However, at pH 12, L/S 20 Al dissolved more....

17 January 2019 159 5 View

Which bacterial media does not have fluorescent properties?

04 July 2017 4,978 5 View

What is the details of Venice Lagoon sand?

22 June 2016 961 2 View

What is the best way or procedure for preparation of expandable vermiculite for intumescent mountain mat for catalytic converters?

What is the best way or procedure for preparation of expandable vermiculite for intumescent mountain mat for catalytic converters?

17 February 2016 4,088 3 View

In NLC system in which temperature this system would release its contents?

In NLC system in which temperature this system would release its contents?

22 January 2016 2,159 1 View

How can we design an algorithm (based on HMM model) for detection genes in unknown genomes?

Which software should be used?

07 December 2015 8,132 4 View

How to analyze a particular region of my simulation box in GROMACS?

Hi, I am using GROMACS 5.1.4 to simulate water in contact with a surface. I am only interested to calculate some properties of water near the surface. Let's say at a distance of x nm from the...

03 March 2021 9,989 2 View

How to get onecolumn document from standard IEEE ACCESS LateX template?

I have prepared a manuscript in IEEE Latex template, but for some purpose, I need to prepare a word file as well (detailed format is not required). Compared to two column .tex file, one column...

02 March 2021 1,830 3 View

How can the modification of garden soil cause global warming?

Hello, I am working on a soil project and I found a primary research article that tests how the modification of agricultural soil can cause global warming, using a thermal collector, however I...

02 March 2021 7,161 3 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

Does anyone know how to plot my station to a section plot on Ocean Data View (ODV)?

I made a vertical section plot with WOA .nc file on ODV, and now I want to plot my stations (csv. file) in it. Does anyone know how to import my points to the section? They are two different...

01 March 2021 3,610 1 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Does anyone know to clarify these changes?

01 March 2021 1,290 2 View

How to assign different material properties to each element in Abaqus ?

Hello, I am writing a python script to generate my model and write the input file. The problem is I have 1000 elements in my mesh and I want to assign different material properties to each...

01 March 2021 9,511 3 View

How to define tie constraint between rigid body and another part in dynamic explicit model of Abaqus?

Hi dear researchers I connected a rigid body into the part of my structure by tie constraint and then I added displacement to rigid body, in static general step every thing is fine and these two...

28 February 2021 3,442 2 View