How to calculate strength degradation in a hysteresis loop (cyclic loading)?

I understand that the peak load at that specific deformation is to be taken but how do we get the % in degradation (is it by % decrease from one load to another)? Additionally, do we compare peak...

09 October 2019 9,975 5 View

Why do some researchers draw coordinate-grid lines on concrete joint especially during beam-column connection testing?

Was it to physically identify crack orientation/inclination and differentiate it between lateral, flexural, shear cracks etc? Or is it for some other function i dont know about.

03 April 2019 4,918 5 View

Is the area under the load-deflection curve of concrete tested under direct shear considered as "shear toughness"?

I tested 100x100x500mm concrete prisms under direct shear using the JSCE-SF 6 standards. Is calculating the area under the load-deflection curve considered as shear toughness or shear energy? The...

31 December 2018 3,493 1 View

What is the function of Field Output Request, specifically the 'every n time increment' in Abaqus?

I've read the manual but i cannot seem to visualize the definition. Say i'm doing a simple reverse cyclic test for a concrete for say, 50mm displacement in 2400 seconds. How does 'every n time...

10 November 2018 2,327 0 View

In Abaqus, how can i select the Reference Point in the .odb output?

I am trying create an XY data from the model via a unique nodal. But the reference point in the .cae model is not visible in the .odb output. Hence i was unable to 'select it from viewport'. Is...

10 November 2018 1,907 4 View

How can i extract XY data from Abaqus ODB File Output using a command line?

I am trying to extract RF3 (Reaction Force) and U3 (Spatial Displacement) from a uniqe nodal postion FOR JUST 1 NODE. but the size of the file is 13 million KB and creating XY data from the...

10 November 2018 8,971 0 View

How to model an Engineered Cementitious Composite in Abaqus?

I've tried using the Concrete Damaged Plasticity parameters but the model just would not work. I'm trying to model a beam-column joint using ECC as the joint material (region intersection between...

10 November 2018 7,842 5 View

How to calculate inelastic strain from concrete uniaxial stress-strain curves?

I conducted compressive and tensile concrete uniaxial test for the Concrete Damage Plasticity (CDP) data in Abaqus. But I only have normal strains under stress, how do i get the inelastic strain?

08 September 2018 4,148 2 View

Is it realistic to have a concrete material with 35 MPa compressive strength (28-days) but with only a 6900Mpa Elastic Modulus?

I conducted a compressive uniaxial stress-strain test for normal concrete, it achieved a peak stress of 35 MPa but when i calculated the young's modulus from the stress-strain curve in excel, it...

08 September 2018 177 14 View

What does a negative inelastic strain mean? should it be included as CDP parameters in Abaqus?

I produced negative inelastic strain in my stress-strain concrete curves (i noticed that mostly negative value were at the elastic/early stage). Do i take the negative inelastic strains and...

08 September 2018 5,279 1 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

How climate change will influences human and animal behavioral change?

The role of climate change influencing the human behavior as well as economics interest

01 June 2021 0 0 View