What are the frame works available for deep learning. and which is the best one to use?

Deep learning Experts Machine learning Experts

11 December 2017 3,586 7 View

Can any one brief me the approaches which yields better performance by trimming or pruning the deep networks ?

Deep Learning Experts Machine learning experts Pattern Recognition Experts

15 October 2017 384 5 View

Which is the best sample preparation method of Graphene for EBSD ?

02 February 2016 1,190 5 View

Can anyone help with Ansys 14.1 transient full mode analysis?

06 July 2015 9,580 3 View

Can you help me with damage parameters in concrete damage plasticity model in Abaqus?

The tensile damage parameter, dt is defined as the ratio of the cracking strain to the total strain. Similarly, the compressive damage parameter, dc is defined as the ratio between the inelastic...

17 March 2015 8,575 19 View

How can I characterize the constituents of alcoholic extract of seeds CASSIA AURICULATA using LCMS data?

I have prepared the alcoholic extract of seeds of CASSIA AURICULATA and subjected for LC/MS to characterise the constituents. I am finding m/e values are more than 500. Is there anybody working...

14 March 2015 4,330 3 View

Getting the strain output in ABAQUS?

12 March 2015 4,299 4 View

Is it possible to obtain Crack Pattern using ABAQUS?

Please refer the attached paper, is it possible to obtain crack pattern directly for flexure without using any specialized techniques in abaqus just by applying loads exceeding the capacity

16 February 2015 4,632 5 View

Why do I get this srror while using concrete damage plasticity model in Abaqus?

Have you come across this error-"DURING THE CONVERSION FROM CRUSHING TO PLASTIC STRAIN Abaqus FOUND NEGATIVE AND/OR DECREASING VALUES OF PLASTIC STRAIN. VERIFY THAT THE DEGRADATION DATA UNDER...

15 February 2015 6,949 12 View

Any advice in applying concentrated load and defining intermediate support in ABAQUS?

Dear Sir/Madam, Kindly help me with following 1.Can we create a concentrated load by creating a reference point and making it "active" in analysis.If so how to make a reference point active in...

15 February 2015 2,469 7 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View

Why the results when using wall thickness and when using shell conduction are different in ansys fluent?

Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...

01 March 2021 9,537 2 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

How to assign different material properties to each element in Abaqus ?

Hello, I am writing a python script to generate my model and write the input file. The problem is I have 1000 elements in my mesh and I want to assign different material properties to each...

01 March 2021 9,511 3 View

How to define tie constraint between rigid body and another part in dynamic explicit model of Abaqus?

Hi dear researchers I connected a rigid body into the part of my structure by tie constraint and then I added displacement to rigid body, in static general step every thing is fine and these two...

28 February 2021 3,442 2 View

How to modify Johnson cook equation in ABAQUS?

I wanted to add an extra parameter to the existing Johnson cook equation in the ABAQUS simulation. How to add those extra parameters. Ref: A modified Johnson-Cook material model with strain...

28 February 2021 4,841 3 View

For modelling epoxy-based matrices (in composites), which model in ABAQUS is the most suitable, Concrete damaged plasticity or Drucker-Prager model?

I am working on developing a micromechanical FE model for predicting kink-band formation in UD composites. To model matrix plasticity, which model, out of Concrete Damaged Plasticity and...

28 February 2021 5,415 1 View

How to find the right number of integration points in second order 3d finite elements?

I am familiar with finite element simulations and numerical schemes like the Gauss Legendre quadrature. I also know that the Gauss integration yields exact values for polynomials up to degree 2n-1...

27 February 2021 6,818 3 View

How can we use a hybrid element in Abaqus Dynamic/Explicit for impressible materials?

Hi, all! How can we use a hybrid element in Abaqus Dynamic/Explicit for impressible materials? I have not find the choice for explicit element in Abaqus CAE. I am wondering whether it is possible...

25 February 2021 9,936 2 View