How define one baker unit(BU) is the amount of hydrogen peroxide catalase ?

07 February 2021 2,006 1 View

Where is the active point of VCSEL?

I am now working on the coupling between vertical-cavity surface-emission laser(VCSEL) and waveguide. However, the window design for laser emission is larger than the waist of Gaussian beam...

27 January 2021 8,318 1 View

Why does COD increase over time when external carbon sources are added in the denitrification process in waste water?

Why does COD increase over time when external carbon sources are added in the denitrification process in waste water? After 1 hour, the concentration increased from 30mg/l to 40mg/l after 20...

17 January 2021 374 9 View

Seperate of organic and inorganic phosphorus in waste water?

Is it possible to separate organic and inorganic phosphorus in wastewater with a filter?

14 January 2021 952 3 View

How to propose constitutive response functions during continuum modeling?

To develop constitutive models in continuum mechanics, one must consider kinematics, balance of momentum, balance of energy, and free-energy imbalance. Next, one must propose constitutive response...

02 January 2021 9,692 4 View

Why use STOP solution in ELISA?

At the last step for data analysis, we always use a STOP solution to stop the TMB oxidized by HRP. Why do we have to stop the reaction? Couldn't we measure the color wavelength of...

17 November 2020 5,177 3 View

How should I explain when the result of CV is good but cyclic charge-discharge is poor in a battery cell test?

I had some CV and cycling test for my battery half-cells. In the CV tests, they were reversible and performed very well. But during the rate performance and the cycling test, they ran only at a...

08 November 2020 7,978 4 View

How to change the title of an article?

Hi All, I have a problem with changing the title of an article added to my account. I have tried to change the title but the attempts always failed. I also tried to add a new one with the correct...

07 September 2020 3,901 3 View

DNA is not precipitating after incubating in ethanol overnight?

I am working on the soil microbiome of heavy metal contaminated soil. I extracted gDNA from the soil sample using the FastDNA Spin Kit and performed ethanol precipitation to clean up the salt...

01 September 2020 3,923 2 View

How to exchange the buffer of peptide ~1KD?

This is a peptide about 1KD in size. The commercially synthesized powder was reconstituted with a citrate buffer(pH 7) and the solution turns acidic, pH ~4. The assay requires a pH at 7 so some...

31 August 2020 870 6 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

Why the results when using wall thickness and when using shell conduction are different in ansys fluent?

Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...

01 March 2021 9,537 2 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

How much pressure we can reduce at the outlet to avoid Reverse Flow?

I am simulating Heat Exchanger. I have tried and tested all the methods to resolve this issue from the internet like refining mesh, improving skewness and orthogonal quality ,extending outlet to...

01 March 2021 6,985 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

How to assign different material properties to each element in Abaqus ?

Hello, I am writing a python script to generate my model and write the input file. The problem is I have 1000 elements in my mesh and I want to assign different material properties to each...

01 March 2021 9,511 3 View

How to define tie constraint between rigid body and another part in dynamic explicit model of Abaqus?

Hi dear researchers I connected a rigid body into the part of my structure by tie constraint and then I added displacement to rigid body, in static general step every thing is fine and these two...

28 February 2021 3,442 2 View

Is anyone familiar with the cyclic compressive fatigue testing (BS EN 12697 - 25) ?

I would like to get more information on the cyclic compressive fatigue testing (BS EN 12697 - 25) which is typically done for bituminous material in pavement design. Any one can advise on the...

28 February 2021 2,004 3 View

How to modify Johnson cook equation in ABAQUS?

I wanted to add an extra parameter to the existing Johnson cook equation in the ABAQUS simulation. How to add those extra parameters. Ref: A modified Johnson-Cook material model with strain...

28 February 2021 4,841 3 View