Hello everybody please how i can make the boundary condition in stepped spillways case 3d ??

Anouar Kaouachi @Anouar_Kaouachi3

07 July 2016 0 4K Report

hello everybody please how i can make the boundary condition in stepped spillways case 3d ??

Badges
Science topic

More Anouar Kaouachi's questions See All

Hello, please why and how we used mesh adabatation im Ansys Fluent ?

Modeling the flow over stepped spillways

03 April 2017 5,272 1 View

Which criteria is used for plotting the residuals for my simulation in ansys fluent ?

Your toughest technical questions will likely get answered within 48 hours on ResearchGate, the professional network for scientists.

03 April 2017 8,657 0 View

What is the acceptable value of the grid convergence index GCI ?

Read 2 answers by scientists to the question asked by Anouar Kaouachi on Apr 24, 2017

03 April 2017 2,852 0 View

Hello how many iterations needed for plot the residual for checking the stable solution in fluent plz ?

Your toughest technical questions will likely get answered within 48 hours on ResearchGate, the professional network for scientists.

03 April 2017 9,225 0 View

Cfd qustion

Hello everyone how i can display the air concertation in ansys fluent please ??

02 March 2016 8,187 1 View

Hello everyone how i can display the air concertation in ansys fluent please ??

02 March 2016 6,354 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View