Cfd qustion - FAQS.TIPS

Anouar Kaouachi @Anouar_Kaouachi3

03 March 2016 1 8K Report

Hello everyone how i can display the air concertation in ansys fluent please ??

Anouar Kaouachi

Hello everyone how i can display the air concertation in ansys fluent please ??

Badges
Science topic

More Anouar Kaouachi's questions See All

Hello, please why and how we used mesh adabatation im Ansys Fluent ?

Modeling the flow over stepped spillways

03 April 2017 5,295 1 View

What is the acceptable value of the grid convergence index GCI ?

Read 2 answers by scientists to the question asked by Anouar Kaouachi on Apr 24, 2017

03 April 2017 2,872 0 View

Which criteria is used for plotting the residuals for my simulation in ansys fluent ?

Your toughest technical questions will likely get answered within 48 hours on ResearchGate, the professional network for scientists.

03 April 2017 8,675 0 View

Hello how many iterations needed for plot the residual for checking the stable solution in fluent plz ?

Your toughest technical questions will likely get answered within 48 hours on ResearchGate, the professional network for scientists.

03 April 2017 9,247 0 View

Hello everybody please how i can make the boundary condition in stepped spillways case 3d ??

hello everybody please how i can make the boundary condition in stepped spillways case 3d ??

06 July 2016 4,394 0 View

Hello everyone how i can display the air concertation in ansys fluent please ??

02 March 2016 6,384 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

Are air moisture harvesting technologies effective in combating desertification?

Air moisture harvesting Air water collection devices

06 August 2024 5,473 2 View

Tangential stiffness option in ansys workbench?

I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...

29 July 2024 2,032 2 View

How to Import Blade geometry from CAD file in ANSYS design modeler?

Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...

27 July 2024 356 3 View

Problem with Two-phase simulation?

Hello; I am conducting a CFD study on two-phase flow in a separator, utilizing refrigerant as the working fluid. For this study, I have implemented pressure inlet and pressure outlet boundary...

25 July 2024 2,309 5 View

How indoor air pollution is sampled using TSI quest EVM air monitoring instrument?

please suggest the research paper related to the instrument is used in it.

16 July 2024 8,453 1 View

Why my simulation results are showing too much deformation compared to experimental result?

I performed fea on tensile dog bone specimen using ANSYS static structural and also tried using ANSYS explicit dynamics. In experimental result the load is 500 N and deformation is 0.6 mm...

13 July 2024 3,631 4 View

How to introduce on fluent the optical loss of the wall due to the reflection of the plate towards the environment ?

"When solar irradiation reaches a surface, some of it is absorbed while the rest is reflected. Part of the light absorbed by the surface transforms into heat and increases the module's...

13 July 2024 8,621 5 View

Can I transfer the 3D file from Matlab to Ansys or Abaqus?

I have a 3D output in the figure section of Matlab, does anyone know a way to transfer it to Abaqus or Ansys? Or in what format should I save it so that these analysis software can analyze it?

09 July 2024 9,226 3 View

How to add a mass source term in the continuity equation?

Hi, I am trying to model laser cladding in Ansys FLUENT. There are two phase: one is base metal surrounded by an inert gas (shown in the image). I want to add a cladding layer of the same metal....

07 July 2024 1,182 8 View