Hello, please why and how we used mesh adabatation im Ansys Fluent ?

Anouar Kaouachi @Anouar_Kaouachi3

04 April 2017 1 5K Report

Modeling the flow over stepped spillways

Sulman Aziz

https://www.sharcnet.ca/Software/Ansys/16.2.3/en-us/help/flu_ug/flu_ug_chp_adapt.html

Usually when complex geometries are involved one use this feature. You can get a lot about this in above link. Regards

Badges
Science topic

Similar topics
Engineering
Modeling

More Anouar Kaouachi's questions See All

What is the acceptable value of the grid convergence index GCI ?

Read 2 answers by scientists to the question asked by Anouar Kaouachi on Apr 24, 2017

03 April 2017 2,872 0 View

Which criteria is used for plotting the residuals for my simulation in ansys fluent ?

Your toughest technical questions will likely get answered within 48 hours on ResearchGate, the professional network for scientists.

03 April 2017 8,675 0 View

Hello how many iterations needed for plot the residual for checking the stable solution in fluent plz ?

Your toughest technical questions will likely get answered within 48 hours on ResearchGate, the professional network for scientists.

03 April 2017 9,247 0 View

Hello everybody please how i can make the boundary condition in stepped spillways case 3d ??

hello everybody please how i can make the boundary condition in stepped spillways case 3d ??

06 July 2016 4,394 0 View

Cfd qustion

Hello everyone how i can display the air concertation in ansys fluent please ??

02 March 2016 8,221 1 View

Hello everyone how i can display the air concertation in ansys fluent please ??

02 March 2016 6,384 0 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

How to determine positive-stained cells in FACS? Use isotype or unstained control?

To compare positive and negative cell populations in flow cytometry, should I compare unstained cells with antibody stained cells? Or with the isotype control? Most papers show comparison with...

06 August 2024 6,728 6 View

Why do we equate male and female arousal?

Women, on the other hand, can become physically aroused (increased blood flow in the reproductive organs) without becoming psychologically aroused even in the slightest. (Robert Weiss)

05 August 2024 9,537 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View