Is there an ideal incubation time of RGO-modified SPCE before subsequent use, i.e., electrochemical characterization or further modification?

I notice that upon washing and air-drying of my RGO/SPCE surface and characterizing again via DPV, the current response towards ferricyanide probe significantly decreases. My worry is that the...

22 February 2021 5,324 3 View

How do you determine Band Gap for a solid, opaque material?

I have seen many answers to the question on how to determine the band gap of a semi-conductor, but that always implies the use of UV-Vis Spectroscopy. However, the problem with this method is that...

28 January 2020 8,981 7 View

How to be more productive while writing?

Do you have any specific schedule when is the best time to write a publication, an article for a journal or an academic book? When is the best productive time for it? Please, share your experiences

29 December 2019 1,705 4 View

Is it wrong to apply multivariate analysis to a group of samples that are different in nature from different publication (i.e., DNA, RNA and protein)?

I am reviewing a manuscript and was wondering if this was a major experimental flaw. Among the eight publications, three used protein, three used RNA, and two used DNA. Apparently, if the...

02 May 2018 2,536 3 View

No title

Hello everyone! I have been consulting this webpage http://beast.community/ and http://www.beast2.org/ , but the examples for the use of BEAUti and BEAST are for old versions. The versions of...

02 April 2018 3,942 3 View

What buffer should I add to the Krebs-Henseleit solution to counteract the rise of the PH while using pure oxygen instead of carbogen?

I am currently working with the Langendorff's Isolated Heart System and I have some problems with the Krebs-henseleit solution due to a change we were force to do after we ran out of carbogen and...

04 October 2017 9,914 2 View

Have you COI sequences of Potamotrygon orbigyi?

24 August 2017 6,634 2 View

How many sequences it needed to put in a crown group to calibrate a tree?

17 August 2017 4,155 2 View

What software do you recommend to calculate flow rates?

Hello. I need to calculate flow rates from precipitation and temperature data. What software do you recommend? Thanks.

04 May 2017 605 1 View

Which model do you recommend for assessing the effects of climate changes on availability and quality water for a supply system?

04 May 2017 9,834 3 View

Physics: Why do we describe light by referring to its wavelength, but microwaves and radar pulses by referring to their frequency?

In physics, the description of the properties of light generally refers to its wavelength (nm), while in the range of microwaves and radio waves we refer to the frequency of a signal (e.g. kHz or...

03 March 2021 1,682 3 View

What is the best way to keep an anaerobic chamber anoxic in the absence of hydrogen?

I'm a graduate student who works with an anaerobe, so I often work in an anaerobic chamber. I've been working on an assay that involves the steady-state of the quinone/ quinol pool. Anoxic...

03 March 2021 2,971 1 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Good sites to recruit survey participants on a grad school student budget?

Any good recommendations for participant recruitment for online surveys on a grad school student budget?

02 March 2021 4,293 4 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Is there any effect of different colours of light (white, red, yellow, blue etc.) on the rate of photosynthesis? If yes, why?

Light is inevitable for the process of photosynthesis reaction. Naturally sunlight plays the vital role for this process. Light may be of different colours like white, red, yellow, blue etc....

02 March 2021 7,890 2 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View