Generate FSK modulated sugnal in cadence?

30 January 2020 1 503 Report

Dear researchers,

i need to generate a FSK modulated signal as input of a receiver front end in cadence how should i generate this signal in cadence?

p.s: i try matlab code and save it in .txt format using pwlf in cadence but after solving fetal errors about increasing time and other errors finally the output of pwlf isn't a FSK signal and looks just like a little spark

Sundara Siva Kumar v

Cadence can be used to design for both front end and backend.

Badges
Science topic

Similar topics
Solid State Physics
Devices

More Ava Khoshgoftar's questions See All

Hi dears, does any one know what kinds of solvent i can use for electrospining collagen type 1?

it would better to be 3D scaffold. I want to culture breast cancer cell lines on that scaffold

07 August 2017 4,965 7 View

Use 6-Hydroxydopamine (6-OHDA) as ROS inducer for MCF-7 breast cancer cell line

27 July 2017 6,566 1 View

staircase ramp using VPWL in cadence ?

how to generate staircase ramp using VPWL signal in cadence ?

27 December 2020 1,521 3 View

MOS Capacitor instance or a mosfet used as a cap (D-S-B connected to gnd)?

Hi, in Cadence Spectre simulations should I use a MOS cap instance or a mosfet (D-S-B connected to gnd) to simulate a real life MOS-cap? I tried both of them and they gave different results i.e....

26 December 2020 6,407 1 View

How to simulate locking range of an injection locked frequency doubler in cadence ?

Hi im trying to simulate an injection-locked frequency doubler (15 to 30 GHz) in cadence, I'm plotting DFT of transient signal to calculate injection locking range or to see injection pulling...

14 November 2020 896 4 View

How to calculate power of Verilog A based Stanford CNTFET model in Cadence Virtuoso?

I have implemented several basic circuits using VS- CNTFET Stanford model in Cadence Virtuoso. All the circuits are showing proper transient response, but power plot is coming out as zero( in...

19 October 2020 2,954 4 View

How can I simulate the effeciency or transmission distance of a circuit?

Dear all, I need to analysis the performance of a circuit. Is there any software that can analysis the efficiency and transmission distance? Can Cadence or LTSpice do this? How?

20 July 2020 826 2 View

Gm (transconductance) shows different values while hand calculated and simulated using spectre?

Vds and Vgs are maintained constant. Still there is a mismatch in the value of gm?

22 March 2020 7,934 7 View

How to simulate the veriloga based Stanford CNTFET model in Cadence?

I am trying to simulate following the instructions in the pdf attached. But I keep getting the following error: "Missing or corrupt .oa file in cellview 'cnt/nCNT/spectre cmos_sch cmos.sch...

11 March 2020 9,590 4 View

How to find write SNM of sram using Cadence Virtuoso?

I am getting the butterfly curve for read SNM but for write snm when i am appling test signal at Q and giving necessary gate signals not getting the curve as i want.

26 February 2020 8,596 3 View

Which circuit design should I use to generate emf oscillating at frequency of 2.5Ghz ?

I am looking for a circuit which can generate an emf oscillating at frequency of 2.5Ghz. My setup is in such a way that, I am passing particles (negligible mass) from a tunnel and want an emf...

21 December 2019 9,800 6 View

How to do theoretical power calculation for any digital cmos circuit? will this theoretical power be verified using Cadence tool?

using Cadence tool we can find average power, total power and peak power. How can we say that the tool is giving correct value? Is there any theoretical analysis for that?

06 July 2019 9,140 4 View