The comparison is made at varying data 8 times, 4 times, 2 times, 1 time and 0 time
for 8 active high clock pulses for switching activity factor
of 100%, 50%, 25%, 12.5% and 0%.
Hi;
A pin should be used instead of the supply voltage. Also, the mentioned pin should be connected separately to the DC supply source. Switching power consumption can be calculated by measuring the current of the supply source.
I would go for an AMS simulation and create a Verilog-AMS block that counts the number of flips on a signal with reference to the clock.
is there any other way to heat a polymer evenly other than oil bath if so what are those and how to use it
06 August 2024 946 1 View
I am looking for a lipid waste disposal method, keeping in mind the environmental, health and safety aspect of lipid waste. Could someone please provide guidelines or the lowest acceptable...
25 July 2024 636 5 View
When Silica gel added in acetone, Silica gel not dissolved in acetone, but acetone form a light blue color solution , why ?
17 May 2024 4,351 0 View
We extracted PAHs from soil with acetone and then we used silica gel for clean up process , but after cleanup we found blue solution. if we used hexane, no color changed. Is this color compound...
16 May 2024 3,288 1 View
Being a researcher in the field of swarm intelligence for more than seven years, I still haven't found any research group/ institution or research lab dedicated to swarm intelligence research....
26 April 2024 4,413 2 View
I have recently published a paper in a Scopus-indexed journal. Is DOI essential? How long will it take to get DOI ? Thanks in advance
08 April 2024 4,092 3 View
composite PCM cooling
13 February 2024 2,002 3 View
how to draw equivalent structure of substrate in ADS software?
04 February 2024 7,367 2 View
WHAT IS RESISTIVE SHEETS AND RESISTIVE INKS? HOW TO USE/GET/DESIGN RESISITIVE SHEETS/INKS IN CST SOFTWARE?
04 February 2024 9,191 1 View
How to use SHM in Cryogenic tank
15 December 2023 3,431 3 View
I am using a Bruker 600M solid-state NMR spectrometer with a Micro 2.5 microimaging system. The test sample is a tube of 1M LiCl aqueous solution, and the nucleus detected is 1H. I am trying to...
01 August 2024 9,225 1 View
Hello!!! I want to implement the Swerling characteristics functions (CF) directly in MATLAB without using its Fourier integral pairs...the Swerling CFs are actually Laplace Transform of the signal...
23 July 2024 4,923 1 View
I'm currently working on the implementation of pulses (legumes) in bakery applications. In one case, pulse flours could be added to bread to increase the nutritional value. Pulses (in particular...
17 July 2024 7,291 3 View
According to various research, soybean is not considered a pulse because of its high fat content.
30 June 2024 6,310 0 View
I am attempting to determine which current inputs (in uA) are subthreshold for inducing a burst of activity. This is because I am attempting to model DBS form epilepsy in vitro, which clinically...
23 June 2024 4,083 1 View
My school recently acquired a Veeco Multimode and Nanoscope IIIa. While our software and computer is set up and working, the actual Nanoscope is not powering on. We currently have it wired up, and...
19 June 2024 592 0 View
I'm a graduate student at UWM focusing on electrophysiology. I'm trying to perform Shaffer Collateral stimulation of CA1 pyramidal neurons. If I were to have a protocol with 6s of no stim, 2...
18 June 2024 319 0 View
I want to simulate an ISFET Array with a read-out circuit in Cadence Virtuoso which can detect electrolyte from a sample solution.
12 June 2024 6,441 0 View
i make a design topology of mixer For my graduation project working at 28 Ghz on cadence with UMC pdk and get this result S(2,1) 3.5db but when trying to make same topology with another pdk on...
09 June 2024 9,729 3 View
How can someone remove different artefacts leading to false results due to electrostatic and flexoelectric effects during PFM measurements? during measurement what steps can be taken to nullify...
02 June 2024 8,241 0 View