17 February 2015 1 1K Report

I want to probe the intracellular expression of an aptamer that I am researching. Just will be some experiments and if someone can send me the vector I can probe the efficiency of it.

Thanks in advance.

More Juan David Ospina Villa's questions See All
What is the density for pva electrospining?

I'm Juan Carlos, a high school student who is working with electropinning, I made an electropinning machine with a 21g needle and a 30kv high voltage source and the distance between my needle is...

28 February 2021 298 3 View

No title

I am trying to find how to know the density needed for a pva electrospinning in a 0.6mm neddle, the electrospinning will be from top to bottom and the problem I really have is the solution because...

25 February 2021 2,615 3 View

HPLC baseline failure (ACN/Water)?

My baseline increases without any explanation, it is only fixed by changing the solution B, will it be the column? Reagents? Bomb? Detector? Solution A: H3PO4 0.01% IN WATER Solution B: H3PO4...

21 February 2021 5,656 3 View

Algorithms to filter corrective max and min from a set of data?

I've got this 5 year Direct Normal Irradiance data I downloaded from https://re.jrc.ec.europa.eu/. I ordered this by year and by every 24 hours because I need the DNI curve by max in summer, min...

17 February 2021 2,777 5 View

How to improve the buffer capacity of sea water?

Hello everyone I would like to improve the buffer capacity of seawater (pH ~8) in order to dissolve as much CO2 as possible without dropping the pH below 7.5 (a range between 7 - 7.5 is...

17 February 2021 2,797 2 View

Resume Book UEP2013 Asian Edition, dis somebodey has it?

I am looking for a copy of the resume book of UEP2013 Asian Edition (Urban Environmental Pollution 2013 Asian Edition) held in Beijing. If somebody has it, please I would like to obtain an...

11 February 2021 2,247 2 View

How do they fill/replace metal hydrides in vessels?

Surely they will want to avoid contact with air/moisture, so what is the procedure for this?

23 January 2021 428 2 View

What type of spectral radiation has greater penetration on materials, UV or IR? What book or source do you recommend for information on this?

I need information concerning the penetration and reflection capacity of ultraviolet and infrared radiation wavelengths on different most common materials. Edit. Can somebody recommend a book to...

16 January 2021 8,051 6 View

What is the easiest and cheapest molecular magnet to synthesize at home and how can it be done?

im looking for a diy at home (home lab) molecular magnet in a chemical suspension that is stable at room temperatures and cheap

30 December 2020 626 1 View

What defines the time it takes to disconnect a molecular switch?

I have been thinking about a material that was made 6 months ago, which is a tetramethylsiloxane linked to a thiazolidinedione and finally to a naphthalene, but I can't find the original paper (if...

30 December 2020 5,347 1 View

Similar questions and discussions
MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

Protein-aptamer gel electrophoresis help, please??

Hi, I have problems with running gel electrophoresis. I have tried agarose gel electrophoresis and native PAGE. I have two proteins, which have molecular weights of ~30kDa and ~180kDa and two...

03 March 2021 4,275 4 View

What kind of fluid could I use for a pitfall trap that also does not invalidate molecular testing?

Hi, I want to start testing pitfall trap to obtain ants samples, but I need to conduct molecular analysis on those insects. So, what kind of fluid can I use? Ethanol expires too early and I need...

03 March 2021 5,978 5 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View

New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before?

Question to you and THEM, the New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before? There appears to be a core problem for...

02 March 2021 3,024 2 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close