09 September 2018 4 3K Report

Currently, I am trying to determine the population genetic structure of two species of nudibranchs from the Caribbean. Previous research has been done with tradicional molecular methods and this is our fist attempt using NGS. So, I would like know if there is a good services provider in order to get the RAD-seq data for our project. DNA extraction is the only step that we're going to carry out in our lab.

Thanks!

More Kimberly García-Méndez's questions See All
Any recommendation to calculate time to dominant design emergence?

Any recommendation to calculate time to dominant design emergence?

01 January 2021 3,809 5 View

Are drones following the e-Auto industry technological trajectory or are they following its own?

* Are drones following the e-Auto industry technological trajectory or it is following its own? * Will drones diffuse faster than electrical vehicles? * Will it depend on the application?, What...

29 December 2020 7,379 3 View

What is the upper and lower limit for plate count for fungi?

I am currently trying to quantify the viable count of trichoderma spp. in a compost sample. However I do not have much literature on the range for plate count of fungi. should I be following the...

19 December 2020 8,874 6 View

Rapid color change in fishes?

I have noted dramatically change in color on the body of some marine fishes. For example, I saw a dramatically change from a "intense-yellow" color to "brown" color (normal color), just in one...

19 October 2020 2,717 6 View

How to decide if to get 1 or various P value? regarding an composting process through time and treatments?

I have a research investigation that I got the results, I applied 4 different composting processes to vegetable waste (manure, manure+Effective Microorganisms, Effective Microorganisms and a...

14 June 2020 2,373 2 View

How to preprocess Waters. raw MSe data using MZmine 2?

I am working with Waters Xevo GS-2 Q-TOF mass spectrometer in MSe mode to analyze and identify phenolic compounds (mainly flavonoids) in a water/metanol extract. But, when i open my .raw files,...

14 November 2019 6,180 3 View

How to cast the Capillary force of a porous media into a body force source term for CFD calculations?

Dear community, I am interested in modeling capillary forces in porous media using the VOF model. The reason for using VOF is mere because of stability. Eulerian-Eulerian is too sensible to IC...

30 April 2019 1,591 2 View

How to connect beam188 and link180 elements in ANSYS APDL?

I am currently working on the design of a deployable truss structure and I would like to know what is the proper way to connect beam188 and link180 elements in APDL? The diagonals (purple lines)...

07 April 2019 3,152 4 View

What is the effect of shorting the secondary of a transformer on the primary?

I would like to understand why if the secondary of a transformer is short circuited the primary winding will also reflect the short circuit despite the fact that they are isolated. Would the...

04 April 2019 4,999 3 View

What is your typical approach for Hybrid HPC computation; MPI-OpenACC ?

After reading the proceeding: "Best Practices in Running Collaborative GPU Hackathons: Advancing Scientific Applications with a Sustained Impact" I came across the paper: "Porting the MPI...

23 August 2018 5,994 17 View

Similar questions and discussions
MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence?

I am on the lookout for the Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence. Does anyone know where I can find it? Thank you in advance

03 March 2021 3,568 1 View

What kind of fluid could I use for a pitfall trap that also does not invalidate molecular testing?

Hi, I want to start testing pitfall trap to obtain ants samples, but I need to conduct molecular analysis on those insects. So, what kind of fluid can I use? Ethanol expires too early and I need...

03 March 2021 5,978 5 View

How to increase a model accuracy ?

dear community, my model is based feature extraction from non stationary signals using discrete Wavelet Transform and then using statistical features then machine learning classifiers in order to...

03 March 2021 6,994 5 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close