Does any body have fluent(mesh) file of this tutorial?
http://dl.racfd.com/tank.pdf
Go to "www.Fluentusers.com"
Franco
Thanks for reply. I did not get it
I am unable to get the hourly solar radiation data of my study area Mumbai, Maharashtra. How can I get hourly solar insolation data of Mumbai, India?
10 November 2018 6,666 12 View
Dear friends I am simulating diffuser with changing divergence angle to check the pressure coefficient If we compare the experimental and computational value, they are not satisfactory. The...
07 August 2017 1,848 4 View
I am doing CFD analysis of waste heat recovery from flue gas to remove moisture content from coal particle. I think This is problem regarding Discrete Particle Method In fluent. But Hoe to add...
02 March 2017 6,892 2 View
I want to simulate cyclone separator with discrete phase and moisture content (evaporation and condensation ) using star ccm. If anybody has tutorial please share it.
01 February 2017 6,066 1 View
we know we can define enthalpy at constant pressure. But what is enthalpy at constant volume? Is enthalpy is equal to internal energy in constant volume process?
10 November 2016 2,917 3 View
I am simulating spray atomizer. Cold Water is rotating through rotating chamber. It comes out as droplet from nozzle.Hot air is coming in contact with water droplet . which model should I use for...
05 June 2016 5,368 8 View
I am trying to simulate rotating spray dryer with water and air as multi phase. I got error in meshing The mesh file exporter failed during translation. Please send your data to your support...
04 May 2016 9,263 3 View
In Ansys workbench we can split face using tool is it possible to split body in ansys workbench? If yes , how?
04 May 2016 2,709 8 View
I am simulating radiator with water as hot fluid and air cooling fluid. water is flowing through tube and air is flowing around tube(like cross heat exchanger). BC Water inlet - mass flow rate...
04 May 2016 9,526 3 View
Does Anybody have fluent model and udf file of this tutorial?
02 March 2016 4,850 4 View
Hello; I am conducting a CFD study on two-phase flow in a separator, utilizing refrigerant as the working fluid. For this study, I have implemented pressure inlet and pressure outlet boundary...
25 July 2024 2,308 5 View
"When solar irradiation reaches a surface, some of it is absorbed while the rest is reflected. Part of the light absorbed by the surface transforms into heat and increases the module's...
13 July 2024 8,620 5 View
Hi, I am trying to model laser cladding in Ansys FLUENT. There are two phase: one is base metal surrounded by an inert gas (shown in the image). I want to add a cladding layer of the same metal....
07 July 2024 1,180 8 View
hello everyone i get into fuent and i select the result icone then i try to create an isosurface but the button is gray so i can't choose it. what's the problem? any suggestion.
03 July 2024 5,418 4 View
Regarding the system coupling issue where the update of the solution component fails, the system coupling update for fluid flow (Fluent) triggered an exception: "Update Solution Failed."
30 June 2024 7,893 1 View
I am modelling CFS Sheath wall in abaqus and i am applying the 100 mm displacement but i am getting high reach force close to 150 kN but i need it till 50kN. I have used mesh independent fastner...
27 June 2024 4,212 2 View
I am simulating 1 cell of PEM with an area of 50 cm². The mesh has an orthogonality of 0.2 for the channels and bipoar plates (polyhedra) and a quality of 1 for the active zones (hexagonal). The...
26 June 2024 2,358 0 View
EMMS - Energy Minimization Multi-Scale
18 June 2024 5,856 2 View
Hello all, I've compiled a udf which reads velocity data with corresponding time stamp from a .csv file using DEFINE_ON_DEMAND macro. Then, I use DEFINE_PROFILE to define an inlet velocity profile...
14 June 2024 6,480 0 View
For the article, I need some references for the subject of checking the convergence of the temperature field parameter for the SPH part in Abacus, and I want to study this case with a few meshes...
13 June 2024 2,504 0 View