I want to simulate cyclone separator with discrete phase and moisture content (evaporation and condensation ) using star ccm. If anybody has tutorial please share it.
Look at this doc. Good luck.
I am unable to get the hourly solar radiation data of my study area Mumbai, Maharashtra. How can I get hourly solar insolation data of Mumbai, India?
10 November 2018 6,667 12 View
Dear friends I am simulating diffuser with changing divergence angle to check the pressure coefficient If we compare the experimental and computational value, they are not satisfactory. The...
07 August 2017 1,849 4 View
I am doing CFD analysis of waste heat recovery from flue gas to remove moisture content from coal particle. I think This is problem regarding Discrete Particle Method In fluent. But Hoe to add...
02 March 2017 6,892 2 View
we know we can define enthalpy at constant pressure. But what is enthalpy at constant volume? Is enthalpy is equal to internal energy in constant volume process?
10 November 2016 2,918 3 View
I am simulating spray atomizer. Cold Water is rotating through rotating chamber. It comes out as droplet from nozzle.Hot air is coming in contact with water droplet . which model should I use for...
05 June 2016 5,369 8 View
Does any body have fluent(mesh) file of this tutorial? http://dl.racfd.com/tank.pdf
04 May 2016 6,445 2 View
I am trying to simulate rotating spray dryer with water and air as multi phase. I got error in meshing The mesh file exporter failed during translation. Please send your data to your support...
04 May 2016 9,263 3 View
In Ansys workbench we can split face using tool is it possible to split body in ansys workbench? If yes , how?
04 May 2016 2,710 8 View
I am simulating radiator with water as hot fluid and air cooling fluid. water is flowing through tube and air is flowing around tube(like cross heat exchanger). BC Water inlet - mass flow rate...
04 May 2016 9,526 3 View
Does Anybody have fluent model and udf file of this tutorial?
02 March 2016 4,850 4 View
Approximate concentrations are require in compared with the WHO permissible limts
11 August 2024 2,722 1 View
I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...
10 August 2024 4,003 2 View
Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...
10 August 2024 6,490 1 View
How do interactions between the biosphere, the carbon cycle, and the water cycle impact global warming and interaction between the atmosphere and the hydrosphere?
09 August 2024 3,287 2 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,047 2 View
One can try to generalize the Vandermonde determinant in the following direction: Let $A$ be any symmetric $n$-order square matrix. Consider its powers' diagonal elements $(A^k)_{ii}$ and...
08 August 2024 6,689 1 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,027 0 View
Hi! So i attempted to understand a novel protein behavior towards heat application by analyzing its secondary structure change. I subjected the protein to a thermal denaturation analysis using...
06 August 2024 1,987 3 View
is there any other way to heat a polymer evenly other than oil bath if so what are those and how to use it
06 August 2024 946 1 View
I have protein-membrane simulations (PDB, PSF, DCD) and have noticed that water molecules near the protein are not visible in the simulations. How can I fix this issue? Is there a way to place the...
04 August 2024 1,200 2 View