I am doing research in confined masonry field where i need different western masonry building codes. If any one has access to them please share.
hi!!
I attach the Mexican masonry building code (in Spanish).
Best regards
Marco
Mexic:
http://confinedmasonry.org/wp-content/uploads/2009/12/47_The-new-Mexico-City-building-code-requirements-for-design-and-construction-of-masonry-structures.pdf
http://www.smie.org.mx/layout/normas-tecnicas-complementarias/normas-tecnicas-complementarias-diseno-construccion-estructuras-mamposteria-2017.pdf
Chile:
https://vdocuments.site/nch-2123-2003.html
Peru:
https://www.humanitarianlibrary.org/sites/default/files/2014/02/design_procedures_for_peru1.pdf
https://www.academia.edu/39289388/NORMA_E.070_ALBA%C3%91ILER%C3%8DA
I found the following link useful:
https://www.nehrp.gov/pdf/nistgcr12-917-18.pdf
I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...
29 July 2024 2,032 2 View
Hello all, i am working on Chilly anthracnose disease and the pathogen involved is colletotrichum capsici but the problem is occuring while subculturing, i can isolate pathogen from chilly fruit...
17 July 2024 1,610 2 View
i want to do a simulation on sma spring in which i deform it and then allow it to regain shape by thermal loading how i can do this in ansys
04 April 2024 9,671 1 View
I use 2% chitosan (w/v) along with 5.6% beta glycerophosphate (w/v) along with 0.1 M sodium bicarbonate. Cell concentration being 2x106 cells/ml. Previously i used MG63 cell lines and they used to...
21 February 2024 9,777 8 View
i want to model a flow through a channel in which water flows from left end and on the top wall a salt concentration is to be provided. i want to see how much salt disolved in water in 100 sec....
20 November 2023 5,412 4 View
I have recorded XRD pattern of RED Copper compound as given in the file below. Can anyone tell how to interpret the XRD and get information.
06 June 2023 8,192 2 View
For magnetic materials, such as ferrites/ manganites/composites, which reitveild software is preferable? (Profex/MAUD/FULL proof/....) If possible for composite system, it should provide detail of...
22 November 2022 4,904 6 View
I prepare composite hydrogel and study its swelling ratio in PBS buffer. So previously the hydrogel used to swell which was recorded from the weight gain in comparison to its initial weight....
23 September 2022 7,587 2 View
The idea is to simulate a double glazed window exposed to solar radiation and see the maximum temperature in the glass. This temperature should be less than the maximum permissible temperature of...
18 September 2022 9,161 0 View
What substrate should be used and what materials should be used for quantum well etc.
22 December 2021 8,584 2 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,028 0 View
Sure, here is the translation: I have a 3D orthogonal woven composite structure where warp, weft, and binder yarns are oriented in three directions. After modeling these yarns and the matrix in...
28 July 2024 8,169 0 View
The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...
27 July 2024 8,508 0 View
Hey All! I am wondering what might be wrong with my band structure. I did the calculations using VASP and plotted the results using Origin. Although I have tried changing various input...
25 July 2024 2,920 11 View
Best method and number of embryos for extracting RNA from pig morulae?
21 July 2024 4,398 1 View
I want to calculate the spin texture for the electronic band structure obtained from SOC calculation. Is there any way for calculation of spin texture using quantum espresso??
19 July 2024 8,571 1 View
I am simulating interlocking / dry stacked masonry in Abaqus. I am using a friction coefficient of 0.6 for my model as it is stated in the previous research as well as in the base paper. The...
16 July 2024 5,047 0 View
Hello everyone, I am currently working on a project involving spatial transcriptomics on E14 mouse embryos. We need to perform cryosectioning without fixing the embryos. Here is the protocol we...
10 July 2024 5,985 0 View
For Polybutylene Terephthalate (PBT) it is known that if you cool it down at fast rates to have an additional melting Peak in DSC-Scans. Androsch et al. (2015) conclude that this is due to...
30 June 2024 2,891 1 View
Greetings everyone. To define the interface between mortar and brick during the modeling of masonry, I need normal and shear stiffness (Kn and Kt). I have tried some relationships found in the...
23 June 2024 6,015 0 View