I am trying to perform a Modal analysis on a thin circular plate. But the results on both the platforms do not match.
Am i doing something wrong?
Hi,
in general, both should produce the same results. However, the default values of some command arguments may vary.
Regards
Please check the boundary conditions, it is very important.
Thanks all :)
Is there any publicly accessible database that recorded electrodermal activity at different conditions?
04 August 2021 1,428 1 View
Changing of standard stainless composition (Iron alloy with minimum % of chromium is 10.5%, 1.2% of carbon and ferrous, carbon chromium) which can improve, a. Anticorrosion properties (chemical...
31 March 2021 8,331 4 View
The pressure drop between the modules in periodic flows (such as in a pipe) is periodic. This pressure gradient can be decomposed into a periodic and linearly varying component. The linearly...
05 June 2020 4,413 0 View
I have experimentally recorded the Sound Pressure Levels of a horn. The SPLs have been obtained through simulation from LMS. But the output of LMS is in the form of spectrum in excel. I want to...
25 February 2017 6,920 5 View
We have a library of compounds to be evaluated for Alzheimer's Disorder
16 February 2017 3,899 4 View
Out of curiosity, I would like to know whether any chemical coating on a substrate change its color when de-ionized water touches it. Precisely, if I pass some water through a microchannel in...
22 October 2016 5,079 3 View
Since, the entanglement occurs mainly in anti-ferromagnetic materials as their spins are aligned in random way. Kindly, let me know how to find out in general a material has the same nature or...
17 October 2016 7,661 2 View
I modeled a simple rectangular plate in ABAQUS to perform a harmonic analysis with 1N force at the centre fixed on the edges and used 'Steady state dynamics, Direct'. But I get '0' velocity...
09 August 2016 5,484 5 View
Upon incubation of my protein with O/N with TEV protease (in 50mM Tris, 0.5mM EDTA), in the morning i saw a white thready precipitated formed. After running the SDS gels, following coomassie...
28 June 2016 5,119 6 View
I would like to know whether it is possible to get vertical side walls in etching of either or silicon wafers using TMAH/KOH based wet etching processes. In general, if I...
12 April 2016 8,914 8 View
I would like to learn more about SPSS and Its application especially in regards to data analysis. Please suggest me how I can learn more about it. Thank you so much.
11 August 2024 9,101 4 View
I have reverse sequences (AB1 format), can I base on reverse DNA sequences to perform nucleotide alignment, convert nucleotides to amino acids and deposit the sequence in GenBank database?
11 August 2024 5,138 1 View
Hello, Why do i see this baseline drift when i compare my blank (black) to the sample (blue)? Any suggestions as to why this happened? Thank you!
11 August 2024 3,770 4 View
Willett, Shenoy et al. (2021) have developed a brain computer interface (BCI) that used neural signal collected from the hand area of the motor cortex (area M1) of a paralyzed patient. The...
10 August 2024 7,180 0 View
I'm currently exploring the application of Python in textile engineering, specifically in areas like data analysis, process automation, and the development of smart textiles. I'm interested in...
10 August 2024 7,429 2 View
How can I use the cif data obtained from rietveld refinement extracted via gsas2, for microstructural analysis using ETEX software?
09 August 2024 7,718 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
Let's say we have a standard, regular hexagonal honeycomb with a 3-arm primitive unit cell (something like the figure attached; the figure is only representative and not drawn to scale). The...
07 August 2024 1,937 1 View
A fungal strain was treated with nanoparticles. We want to do an environmental SEM analysis. So could anyone share your views on preparing the sample? Thank you.
07 August 2024 5,307 1 View
Hi, I have a question about normalizing the MTT OD values for doing the statistical analysis. So, if we have 3 different plates and we call them 3 different replicates, so, first we would...
07 August 2024 8,106 4 View