hello every one,
my question is can someone explain in detail why is
The delamination buckling load increase with the increase of depth position of delamination along the thickness?
thank u
Hi Ismail
could you explain clearer?
Look at this doc it may be helpful for your topic. Good luck.
hello every one good day. i am using abaqus to perform a non linear buckling analysis in order to match it the experimental buckling load ,i have to use imperfection in my model but Increased the...
04 May 2017 8,904 4 View
Hello Everyone , I am performing a buckling analysis on laminated composites shells. The load I am getting in Non Linear Riks method is greater than the Eigen Value Load . Can someone help me with...
04 May 2017 2,367 2 View
hello every one. i performing delamination buckling on composite shell with cutouts...the result show that the buckling load for Filleted square cutout is less than that of the square shape...
09 October 2016 4,192 1 View
hello every one i want to create this type(picture attached) of mesh around the cutouts in abaqus can any one help me and tell me the step wise procedure how i can create this....picture is...
31 December 2015 5,413 6 View
hello every one... i m modeling composite laminates consist of an UPPER and Lower part which are tied through a cohesive elements, the stacking sequence is [45/0/-45/0/45/0/-45/0/45/0]2s... Where...
09 October 2015 8,721 6 View
hello can any one help me how can i generate this type of mesh in abaqus as shown in the attached file ,,more refined mesh near the cutouts and bigger size away from the cutouts..i dont know if...
09 October 2015 7,199 2 View
hello every one i want to create zero thickness cohesive element IN ABAQUS by using orphan mesh technique from the existing part,,, when i do that an error occur which say "The node numbering...
09 October 2015 9,720 3 View
hello every one.... i m modeling delamination using a zero thickness cohesive element in Abaqus . consider two plates and a zero thickness cohesive element in between them.. i create an orphan...
09 October 2015 7,457 8 View
Hello every one..i would be glade if some one could explain to me the difference between creating a solid composite layup and continuum shell lay up(1) How are the plies are assigned to the...
08 September 2015 5,611 1 View
Hello,,,,,,Everyone i m modeling a delamination buckling of composite laminates using cohesive element I M USING ABAQUS STANDARD 6.14 FOR MODELING,,,Model description is like this IT have two...
08 September 2015 9,358 5 View
I would like to learn more about SPSS and Its application especially in regards to data analysis. Please suggest me how I can learn more about it. Thank you so much.
11 August 2024 9,101 4 View
I have reverse sequences (AB1 format), can I base on reverse DNA sequences to perform nucleotide alignment, convert nucleotides to amino acids and deposit the sequence in GenBank database?
11 August 2024 5,138 1 View
Hello, Why do i see this baseline drift when i compare my blank (black) to the sample (blue)? Any suggestions as to why this happened? Thank you!
11 August 2024 3,770 4 View
Willett, Shenoy et al. (2021) have developed a brain computer interface (BCI) that used neural signal collected from the hand area of the motor cortex (area M1) of a paralyzed patient. The...
10 August 2024 7,180 0 View
I'm currently exploring the application of Python in textile engineering, specifically in areas like data analysis, process automation, and the development of smart textiles. I'm interested in...
10 August 2024 7,429 2 View
Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...
10 August 2024 6,493 1 View
How can I use the cif data obtained from rietveld refinement extracted via gsas2, for microstructural analysis using ETEX software?
09 August 2024 7,718 0 View
Let's say we have a standard, regular hexagonal honeycomb with a 3-arm primitive unit cell (something like the figure attached; the figure is only representative and not drawn to scale). The...
07 August 2024 1,937 1 View
A fungal strain was treated with nanoparticles. We want to do an environmental SEM analysis. So could anyone share your views on preparing the sample? Thank you.
07 August 2024 5,307 1 View
Hi, I have a question about normalizing the MTT OD values for doing the statistical analysis. So, if we have 3 different plates and we call them 3 different replicates, so, first we would...
07 August 2024 8,106 4 View