As above and i'm not sure why do the cells not remain in 3D aggregates. I tried to mix 2 cell types together and they do not "stick". What are the possible reasons for this? Thank you.
Hello Justin. What protocol do you use for your 3D culture?
Dear Alexandra, i'm using ultra low attachment surface to grow my 3D cultures. Does this negatively affect intercellular adhesion?
Dear all, good day! I have a question regarding the use of NaOH for lysis of mammalian cells. Is it a common practice? Are there any publications which have used NaOH to perform cell lysis? If...
03 April 2019 5,439 4 View
Dear all, recently i did a scratch test migration assay on my test compounds incubated with my cell line of interest and it appeared that the cell line seem to exhibit signs of increased cell...
10 November 2018 476 5 View
Dear all, recently i am considering if i have been doing my MTT assay wrongly as i have been using my media (with 10% FBS) for my cell viability assay. I realised that the cells were dying at high...
10 November 2018 9,000 2 View
Dear all, Recently i have a really crazy and brilliant idea to determine if a compound would be able to increase / decrease the motility of a cell type towards another cell type. How should i go...
09 October 2018 3,029 5 View
Dear all, recently i found some strange and uncanny sights in the wells of cells treated with my compound of interest. Apparently when i checked the water solubility of the compound of interest,...
09 October 2018 1,527 3 View
Dear all, i have recently discovered that one of my test compounds is able to promote intercellular aggregation (i.e. the cells are aggregating when treated with the compound). However, i can only...
04 May 2018 7,303 1 View
Dear all, recently i started a cell viability study using presto-blue reagent for the testing. However, i dissolved the drug of interest in sterile water before adding into the wells (96 well...
04 May 2018 9,061 0 View
As above. Thank you :)
10 November 2017 6,358 0 View
10 November 2017 9,345 1 View
10 November 2017 7,777 4 View
I have carried out MFC experiments on three different volumes, 50, 500 and 1000 mL of wastewater. Results after MFC treatment shows that TDS and EC are more in larger volumes of water i.e. TDS and...
09 August 2024 9,621 0 View
Hello everyone! I observed in my culture (htert-RPE1 cells) an orange- red particle at the bottom of the dish. It is visible to the naked eye as a very very small red dot. Could it be a...
09 August 2024 2,824 3 View
I am working in fungal fermentation of soybean meal and there is bacterial growth in them at times. I am trying to quantify fungal cell counts and bacterial cells; but I haven't been able to do at...
07 August 2024 7,535 4 View
Hi, I have a question about normalizing the MTT OD values for doing the statistical analysis. So, if we have 3 different plates and we call them 3 different replicates, so, first we would...
07 August 2024 8,106 4 View
Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...
06 August 2024 9,986 2 View
Previously when I co-coluture anti-CD19(FMC63) CAR-Jurkat with Raji with E:T=5:1, Jurkat can eliminate Raji in 24h. However, when I test another CAR construct, although I can dectect totally CD69...
06 August 2024 641 2 View
i have sorted anti-NP specific plasma cells from bone marrow of C57BL/6 mice at certain times after immunization with variable counts and isolated total RNA using TRIZOL method for RT-PCR using...
05 August 2024 8,835 1 View
I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...
05 August 2024 3,665 0 View
I have tried several times to isolate lymphocytes from mouse spleen, but all attempts have been unsuccessful. I tried most available protocols. I used different dissociation media (HBSS with Ca...
04 August 2024 9,913 7 View
I have protein-membrane simulations (PDB, PSF, DCD) and have noticed that water molecules near the protein are not visible in the simulations. How can I fix this issue? Is there a way to place the...
04 August 2024 1,200 2 View