QTL, recombination frection?

22 February 2021 2,588 2 View

What are the dimensions by which the independent variable (big data) can be measured, Knowing We using the questionnaire instrument?

We have a research project consisting of three variables where big data is the independent variable. Some previous studies showed that Volume, Variety, Velocity and Veracity Are the dimensions...

21 February 2021 8,133 2 View

How can we determine the band gap of a composite material that is made up of a composition of direct and indirect band gap semiconductor materials?

I have a direct band gap material and an indirect band gap material. If I made a composite of both through physical mixing. Then how can I determine the band gap of such a material as the Tauc...

17 February 2021 8,104 4 View

What Electrolyte Solution should be used for EIS and CV, While material I'm using is Carbon doped Titania as a counter electrode in DSSC?

Hope so, you are all fine, I want to perform EIS and CV of my material Carbon doped Titania as a counter electrode for DSSC, I just want to know what electrolyte solution and in what molar...

25 December 2020 7,095 3 View

How to determine the sample size for ANOVA in GPower?

Hi, I am going to execute an experiment with the four categorical variables (A=2 levels, B=2 levels, C=2 levels, D= 5 levels) and one dependent continuous variable. There are total of 40 groups...

19 December 2020 3,600 4 View

What are the free fee journal in Scopus or Clarivate classification deal with geotechnic ?

I want to introduce my manuscript to journal which is not take fee on publishing.

15 November 2020 609 3 View

Why the crystallographic plane (100) has higher growth rate than other planes such as (220), (111) in (100) oriented crystal?

Dear All, Here I have an interesting question that comes to me about crystallographic planes and growth rate. The literature survey shows, the (100)-oriented crystals the crystallographic plane...

06 November 2020 9,490 10 View

Can we co-relate that A-site vacancies are one of the main reasons for (110)-texture formation? But how?

A-site deficient 0.1BiScO3-BaTiO3 (BSBT) thin films were deposited on Pt/TiO2/SiO2/Si substrate by using PLD. XPS results revealed that A-site vacancies increase with the increase of deposition...

05 November 2020 9,281 1 View

Difference between Data-Driven Adaptive Robust Optimization and Adaptive Robust Optimization?

Could you make some points about the difference between Data-Driven Adaptive Robust Optimization and (classic) Adaptive Robust Optimization?

01 November 2020 9,653 3 View

Can anyone tell me that how to find dangling bond in GaN, AlN or AlGaN?

I want to know about the dangling bond? by which method we can find it, does its need some special type of characterization just like XRD etc... or method i want to find dangling bond effect in...

26 October 2020 1,938 6 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View

Complex wave form in ANSYS?

Is there a way to input wave speed in a complex form on ANSYS? The wave speed I need to assign a material is 325(1+0.11i) however I have been unable to do this thus far. Failing that, is there...

27 February 2021 5,969 1 View

What is the best way to calculate the angles of twist for concrete columns subjected to torsional moment using finite element software?

In Finite element software like ANSYS , there is difficulty in obtaining direct results of twisting of concrete members because SOLID65 which is the unique element designed to represent concrete...

26 February 2021 3,806 2 View