Special issue on PLS-SEM in Mathematics. Are you interested?

21 February 2021 5,601 3 View

Aspen plus (hydrometallurgy set-up) & reactions solid-liquid ?

I have to simulate a hydrometallurgical process where there are the following phases: - leaching (solid-liquid reactions) - cementation (solid-liquid reactions) - electrowinning (energy ) -...

30 January 2021 9,225 3 View

In opensees is the ReinforcingSteel material sensitive to units of measure?

20 January 2021 7,043 2 View

Could you help with a doubt regarding UDF velocity inlet profile with multiphase mixture (Ansys Fluent)?

We are two undergraduate students seeking for help!!! We are trying to simulate a laminar flux through a 3D pipe (25 cm long, 2 cm of diameter) consisting of a multiphase flux (air and water). We...

23 November 2020 3,918 3 View

How should I dispose of silver staining waste (SDS-PAGE)?

I know I cannot pour silver staining waste down the sink, but how should I dispose of it? Thank you in advance!

18 November 2020 1,745 3 View

How to generate pulsed laser from CW laser?

I was wondering if it could be possible to modulate a CW laser to pico/nano seconds pulsed laser somehow. I need to generate that condition to pump DFB polymeric lasers. Probably using...

16 November 2020 7,601 3 View

Which dose do you expose RAG1 deficient mice for lethal-irradiation?

Hello, I'd like to apologize for my English in advance, I'm still trying to polish it. We are performing several bone marrow transplantations (BMT) or fetal liver transplantations (FTL) to...

05 November 2020 4,239 1 View

How can I obtain the cohesive energy density and solubility parameter for a crystal using the Materials Studio software?

Hello, I am currently analyzing properties of some minerals such as Bi2O3 by MD using Materials Studio, I need to obtain the cohesive energy density (CED) to obtain the solubility parameter,...

02 November 2020 4,356 1 View

Grounded theory or Interpretive phenomenological analysis? Which is best for dissertation studying perinatal mental health?

I am curious what the differences are between using grounded theory or interpretive phenomenological analysis (IPA) for my dissertation. I am seeking to both complete my dissertation for...

29 October 2020 3,066 4 View

How to calculate grain size if FWHM of Lorentzian contribution is nearly zero and lower that FWHM of instrument?

I want to calculate grain size and microstrains. I fitted my peaks with a Voigt function but the FWHM of the Loretzian contribution resulted to be nearly zero, lower than the FWHM obtained from...

28 October 2020 2,578 1 View

Why the results when using wall thickness and when using shell conduction are different in ansys fluent?

Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...

01 March 2021 9,537 2 View

How much pressure we can reduce at the outlet to avoid Reverse Flow?

I am simulating Heat Exchanger. I have tried and tested all the methods to resolve this issue from the internet like refining mesh, improving skewness and orthogonal quality ,extending outlet to...

01 March 2021 6,985 3 View

Is IMPACT FACTOR justified in case of Taxonomy?

There is huge pressure of getting good impact factor on scholars now a days. On the other hand Taxonomy is a very dry subject and the concerned papers can only get citation in same group of organism.

26 February 2021 5,851 1 View

How to measure angle between laser travel path and machine axis in Laser Measurement system?

25 February 2021 1,987 3 View

Uncertianiny in using dry or wet basis in mixing a sediment with fuel oil?

Hello I'm currently working on a topic related to studying the anaerobic biodegradation of TPH in marine sediments. In this work, sediment should be mixed with fuel oil to a concentration of 20 g...

24 February 2021 9,839 3 View

How do you mesh a thin solid in Fluent?

Hello, I have used the shell function on SpaceClaim to create thin solids for the model I am studying. These are contained within an enclosure for my study. I chose this approach as it avoids the...

24 February 2021 8,856 3 View

Standard curve shifting over time. How do I stabilise the ELISA?

24 February 2021 1,365 3 View

How can I selectively dry etch Ti on a polymer substrate?

24 February 2021 5,378 1 View

Why does the sum of reaction forces not match the force component of a Free Body Cut in Abaqus?

I am using Abaqus to simulate a plate with in-plane loading. The boundary conditions allow the right edge to move up and down, the displacements on the left edge are fixed. There is no rotation...

23 February 2021 711 3 View

How to reduce static electricity of powder after lyophilization?

I am working on synthesizing and then purifying peptides using the SPPS system. After purification of the peptide, the peptide powder is obtained using a freeze dryer. When measuring the powder,...

22 February 2021 10,099 5 View