Coating of metal surface with wash coating and dip coating?

09 September 2013 0 2K Report

I want to make a metallic coating with a catalytic matter like synthetic clay. Can you give me information about this method, or information on papers?

Badges
Science topic

More Hüseyin Gümüş's questions See All

Do plasmonics loss performance when they are immobilized in polymer matrix?

Of course it depends on the immobilization technique, concentration and other parameters. I would like to contact scientist who study plasmonic materials.

01 February 2017 2,549 0 View

How can we calculate hkl values of a sample from its XRD spectrum?

In the articles it is given 2 theta value with crystal plane of the sample for example, 18,5 degree (001). I use Rigaku software and hkl calculation icon is inactive. How can we calculate hkl...

01 February 2015 1,167 11 View

Which polymerization initiator can be used for acrylic acid grafting to PVDF?

To graft acrylic acid (AA) to PVDF what is the best initiator oxidant? potassium persulphate and other organics?

11 December 2014 2,092 3 View

What are the GC column conditions for benzimidazoles?

I need your help with an analysis of 2-aryl benzymidazoles at Gas Cromotography (GC). What are the column conditions, i-column type, ii- most effective solvent and dilution amount, iii- column...

31 December 2013 6,588 2 View

How can safe injection be performed to Gas Chromatography?

I mean how can we make clean our sample before injection? As we know, the cleaner our sample in terms of particles or abrasive chemicals, the longer our column can be used. Although i am aware of...

06 July 2013 6,582 2 View

Which method is advantageous for catalysis reactions? Solvent or solvent-free.

I am planning to do a reaction in the solvent free area. Because solvents may influence our solid catalyzer by absorbing on or solving it, the catalyzer which I will use is a clay type.

01 February 2013 1,628 14 View

Adherance of Polyaniline coating over stainless steel?

Is the electropolymerisation of polyaniline coating over stainless steel (SS) via Cyclic voltammetry technique is really adherant? Else how to improve the adhesion of the coating, whether any...

01 March 2021 8,220 2 View

Is there a method of determining feed digestibility without the need to re-pellet the feed?

I am aiming to determine the ADC values of a commercial fish feed, but I do not have a steam pelleter or extruder available to me. Ideally, the pellets could be coated with some inert marker....

28 February 2021 7,967 3 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

How to immerse bricks in wax ( for coating ) ?

Do we immerse the bricks horizontally or vertically ? #bricks#waterproofingsurface#civil#engeenering#chemicalengineering#wax#parafinwax

28 February 2021 6,685 2 View

For gelatin coating for culturing HUVEC.Should the gelatin be made in sterile water or PBS? Do I need to autoclave the gelatin soln after making it ?

I want to use 0.1% gelatin. Should that be made in PBS or sterile water? Should I autoclave the gelatin soln after making it in water/PBS?

28 February 2021 274 2 View

Why is my platinum counter electrode getting dirty during electrodeposition?

I am conducting anodic electrodeposition of MnO2 onto a stainless steel substrate, using a platinum strip as a counter electrode. This is done galvanostatically, with the current held between 5...

27 February 2021 1,829 3 View

What pH condition required to coat APTES on silica coated Fe3O4?

It's a hydrolysis reaction, which may produce by either acid or base-catalyzed reaction. so can anybody help me with this, which condition is suitable for this reaction?

26 February 2021 1,760 8 View

What is the best surface to culture cells isolated from a skin biopsy?

Hello, recently I am having some difficulties with maintaining the cell culture of primary cells isolated from a skin biopsy (normal and malignant). The coating of culture plates with Matrigel (a...

26 February 2021 6,151 2 View

Unknown debris sheets observed in cell culture flasks?

Hi, We culture neural progenitor cells in T175 culture flasks coated with PLO-Laminin. We have successfully grown these cells with our protocol for months. Recently, we observed large sheets...

25 February 2021 3,443 4 View

How does charge on working electrode changes with rising potential?

During performing CV of a GCE or modified GCE, we rise the potential in the first half of the cycle and reduce it in reverse half. During the first half, what is the nature of charge on GCE or...

25 February 2021 7,994 3 View