Of course it depends on the immobilization technique, concentration and other parameters. I would like to contact scientist who study plasmonic materials.
In the articles it is given 2 theta value with crystal plane of the sample for example, 18,5 degree (001). I use Rigaku software and hkl calculation icon is inactive. How can we calculate hkl...
01 February 2015 1,590 11 View
To graft acrylic acid (AA) to PVDF what is the best initiator oxidant? potassium persulphate and other organics?
11 December 2014 2,198 3 View
I need your help with an analysis of 2-aryl benzymidazoles at Gas Cromotography (GC). What are the column conditions, i-column type, ii- most effective solvent and dilution amount, iii- column...
31 December 2013 6,695 2 View
I want to make a metallic coating with a catalytic matter like synthetic clay. Can you give me information about this method, or information on papers?
08 September 2013 2,024 0 View
I mean how can we make clean our sample before injection? As we know, the cleaner our sample in terms of particles or abrasive chemicals, the longer our column can be used. Although i am aware of...
06 July 2013 6,691 2 View
I am planning to do a reaction in the solvent free area. Because solvents may influence our solid catalyzer by absorbing on or solving it, the catalyzer which I will use is a clay type.
01 February 2013 1,740 14 View
How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...
10 August 2024 942 3 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
One can try to generalize the Vandermonde determinant in the following direction: Let $A$ be any symmetric $n$-order square matrix. Consider its powers' diagonal elements $(A^k)_{ii}$ and...
08 August 2024 6,690 1 View
We intend to study the interaction between peptides and polymer (like PP, PE and PS) through MD simulations using Martini force fields ( Martini 2 for PP and Martini 3 for PE, PS). We have...
08 August 2024 4,842 0 View
is there any other way to heat a polymer evenly other than oil bath if so what are those and how to use it
06 August 2024 947 1 View
After immunohistochemistry of previously fixed in PFA and EtOH and then frozen 20 μm sections of zebrafish brain, DAPI staining is very weak (right) compared to the same sections stained without...
05 August 2024 9,637 2 View
Have you ever seen a LC-MS/MS method uses both internal standards and external standards (in matrix matching purpose) but the concentrations of internal standards are outside the calibration curve...
05 August 2024 3,084 6 View
I have tried several times to isolate lymphocytes from mouse spleen, but all attempts have been unsuccessful. I tried most available protocols. I used different dissociation media (HBSS with Ca...
04 August 2024 9,913 7 View
- The Existence/Uniqueness of Solutions to Higher Order Linear Differential Equations - Higher Order Homogenous Differential Equations - Wronskian Determinants of $n$ Functions - Wronskian...
03 August 2024 2,366 0 View
I need to lyse and homogenise mouse tissues. So far I have experimented with liver and lung tissue, using matrix D. The liver was completely lysed with 6 repetitions of the standard program, but...
31 July 2024 9,186 0 View