CFD ANSYS FLUENT VOF SIMULATION SOLAR DESALINATION?

More Ahmed Alkaisi's questions See All

Divergence detected in AMG solver?

Dear Sir/ Madam, I need your assistance, please. I see the following error message after run calculation of ANSYS-Fluent. “Divergence detected in AMG solver: temperature” How can I overcome this...

06 July 2016 9,442 6 View

Hi, Can anyone help me in Solar Still evaporation condensation CFD simulation, please?

Hi, I am doing a simulation for a double slope solar still. there is evaporation from the water surface in the basin and water condensation on the glass cover I need some help if anyone can send...

06 July 2016 2,318 5 View

Is VOF model a successful tool to solve evaporation-condensation problem?

Hi, Thank you for your help. Just to remind you, I am a PhD student. I am working on a Solar Still, water evaporation-condensation. 1- Water in the tank evaporate due to solar radiation. 2- Water...

01 January 1970 1,896 5 View

Is (ANSYS- Fluent> multiphase> VOF model) an appropriate tool to simulate the evaporation-condensation in a solar still desalination system?

Hi,I am a PhD studentI am working on ANSYS- Fluent> multiphase> VOF modelI want to simulate the evaporation-condensation in a Solar Still Desalination systemDo you have any tips and tricks...

01 January 1970 549 4 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Stability of the Solar System: Insights from Einstein’s Equations ?

The stability of the Solar System is a complex subject that blends the classical framework of Newtonian mechanics with the modern insights provided by General Relativity (GR). Understanding this...

07 August 2024 2,569 1 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

How to determine positive-stained cells in FACS? Use isotype or unstained control?

To compare positive and negative cell populations in flow cytometry, should I compare unstained cells with antibody stained cells? Or with the isotype control? Most papers show comparison with...

06 August 2024 6,728 6 View

Why do we equate male and female arousal?

Women, on the other hand, can become physically aroused (increased blood flow in the reproductive organs) without becoming psychologically aroused even in the slightest. (Robert Weiss)

05 August 2024 9,537 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

Panayampilly abubucker abdul samad

Can you send details to my e maik id, [email protected]

Ajaz Rashid

It is generally easier to predict the evaporation rate using equations that exist in the literature. And for many cases, you can assume that all the vapor does eventually condense (i.e evaporation rate = condensation rate) with very small error.