Is it acceptable to write a paper without any reference? If so, will it be accepted? Can we write one page journal paper? To the point discussion would be possible or not? What are the consequences? Can we write paper with patent reference?
I don't think so
What is the influence of literature review for any journal paper? How do acess the quality of the paper based on Literature Review?
03 April 2019 3,514 4 View
How far the research is being utilized for social cause? Is research given more importance than it is supposed to be given? How far these research papers, articles, letters etc. influence the...
04 May 2018 4,667 9 View
Is there any good coupling interfaces available for ANSYS (FEM) and Electro Discharge Machining (EDM)? The heat transfer rate across the plasma zone, the temperature distribution along the...
04 May 2018 7,786 3 View
Is it good to write the "Conclusions" section lengthy or precise in a journal paper? Kindly suggest.
04 May 2018 7,337 17 View
The experimental data is the necessity in analyzing our responses w.r.to different influencing parameters. But it is observed, in recent past, most of the researchers are publishing graphs and...
04 May 2018 6,805 8 View
The mental trap or struck in between while doing the research work or writing a journal paper occur often in our life. We often get confused how many papers should be referred for writing a paper....
04 May 2018 4,646 3 View
As the depth of cut increases in EDM process, the over cut on the material also increases because the spark is generated round the electrode. What precautions should be considered in designing the...
04 May 2018 4,450 2 View
The plasma zone is the cause for removing the material from the work piece as well as from the electrode. What could be the temperature range of plasma during Electro Discharge Machining (EDM)?...
04 May 2018 6,288 1 View
What is the correctness of SEM, TEM and EDX analysis? What is the percentage of error? How do you calibrate the machine? I have got some data from the internet source. I request suggestions from...
04 May 2018 2,659 5 View
What are the general trends in Electrical Discharge Machining Process for MRR, TWR, SR, other responses with Current, T on, T off, Servo Voltage etc? For different materials like Al, Al alloys,...
04 May 2018 6,521 2 View
This article is mine. It was republished by unknown person using an address (Wilson N Jones Regional Center, Sherman Texas USA. I have a patent.
10 August 2024 7,528 5 View
I am Looking for a Science Journal with good impact factor and low publication cost to publish a review paper. Your suggestions would be appreciated.
06 August 2024 6,796 3 View
Hi everyone, If you have written or come across any papers where Generalised Linear Mixed Models are used to examine intervention (e.g., in mental health) efficacy, could you please share the...
04 August 2024 4,130 4 View
HOW CAN I WRITE A CODE TO USE THE WAVENET TRANSFORM AS A FEATURE EXTRACTION METHOD INSTEAD OF DWT IN MATLAB?
03 August 2024 7,829 0 View
As authors and academic writers, we usually prepare our manuscript using our own resources. We submit these manuscripts to scientific Journals for peer review and publication sometimes at a fee....
03 August 2024 7,304 2 View
I want to write a topic for my PhD thesis in hospitality (hotels), can u please suggest some variables
29 July 2024 9,058 3 View
a 15-page paper
29 July 2024 1,956 5 View
In hirshfeld surface calculation i did not find any red spot in hirshfeld surface, is it ok for research article to write?
28 July 2024 2,988 0 View
Looking for paper collaboration writers: Collaboration Model 1: 1.1 Based on the chosen topic, complete the paper writing, select an SCI or SSCI Q1 journal, submit using my QRCID, and complete...
27 July 2024 8,965 1 View
Today, many priorities for improvements to teaching and learning are unmet. Educators seek technology-enhanced approaches addressing these priorities that would be safe, effective, and scalable....
26 July 2024 8,544 4 View