What are the general trends in Electrical Discharge Machining Process for MRR, TWR, SR, other responses with Current, T on, T off, Servo Voltage etc?

More Jonnala Subba Reddy's questions See All

What is the influence of literature review for any journal paper? How do acess the quality of the paper based on Literature Review?

03 April 2019 3,514 4 View

Can we write any journal paper without a single reference?

Is it acceptable to write a paper without any reference? If so, will it be accepted? Can we write one page journal paper? To the point discussion would be possible or not? What are the...

10 November 2018 9,691 1 View

What is the social responsibility of the Research Scholor and doctoral candidate?

How far the research is being utilized for social cause? Is research given more importance than it is supposed to be given? How far these research papers, articles, letters etc. influence the...

04 May 2018 4,667 9 View

Is there any good coupling interfaces available for ANSYS (FEM) and Electro Discharge Machining (EDM)?

Is there any good coupling interfaces available for ANSYS (FEM) and Electro Discharge Machining (EDM)? The heat transfer rate across the plasma zone, the temperature distribution along the...

04 May 2018 7,786 3 View

Can the "Conclusions" section be written lengthy or precise in a paper?

Is it good to write the "Conclusions" section lengthy or precise in a journal paper? Kindly suggest.

04 May 2018 7,337 17 View

Is it fair enough to publish experimental data in a peer reviewed journal? Or is it better way to publish data with graphs without publishing data?

The experimental data is the necessity in analyzing our responses w.r.to different influencing parameters. But it is observed, in recent past, most of the researchers are publishing graphs and...

04 May 2018 6,805 8 View

What is mental trap (The situation where we get struck while doing our research or a jouranl paper etc.) ? How to overcome the mental trap?

The mental trap or struck in between while doing the research work or writing a journal paper occur often in our life. We often get confused how many papers should be referred for writing a paper....

04 May 2018 4,646 3 View

What is the influence of electrode in EDM when it is cut / drill deep into the workpiece?

As the depth of cut increases in EDM process, the over cut on the material also increases because the spark is generated round the electrode. What precautions should be considered in designing the...

04 May 2018 4,450 2 View

What is the temperature range in plasma zone in EDM process?

The plasma zone is the cause for removing the material from the work piece as well as from the electrode. What could be the temperature range of plasma during Electro Discharge Machining (EDM)?...

04 May 2018 6,288 1 View

What is the correctness of Scanning Electron Microscopy (SEM), Transmission Electron Microscopy (TEM) and Energy Dispersive X-ray Analysis (EDX)?

What is the correctness of SEM, TEM and EDX analysis? What is the percentage of error? How do you calibrate the machine? I have got some data from the internet source. I request suggestions from...

04 May 2018 2,659 5 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

How does grain and grain boundary affect the ceramic when studying its dielectric properties?

I am not able to get good literature and the physics behind how first these grains and grain boundaries arises out of no where when we make a pellet to study its dielectric properties and then how...

07 August 2024 5,177 3 View

Why is the molecule's orientation with an electric field affect polarizability?

Why is the molecule's orientation with an electric field affect polarizability? Electrons are diffuse enough to be independent with respect to orientation and effect of electric field on...

03 August 2024 7,843 1 View

Hello, regarding Mxene 2D titanium carbide?

I fabricated Ti3C2Tx using concentrated HF 40%, I plot an XRD as attached image below.. please let to know if I obtained it or not.

02 August 2024 6,789 4 View

Does continues partial charging/discharging do any harm to the BESS performance and degradation?

For a grid connected BESS (lets say 100 MW/200 MWh system, LFP battery), if we charge the BESS in such a way that whenever we can access power from the solar that will charge the BESS. Hence it...

01 August 2024 9,903 7 View

What should be the sample container for the hydrothermal reaction in a microwave reactor at 180 °C for 10 min at the heating rate of 5 °C per minute?

Suggest one of them 1. Teflon-lined stainless steel autoclave: 2. Alumina (Al2O3) ceramic container

30 July 2024 7,326 1 View

Ti6Al4V - Phase differentiation between alpha and alpha prime martensite?

Dear Researchers, Is it feasible to distinguish between alpha and alpha prime martensite in the Ti6Al4V alloy under rapid solidification in the as-cast state using XRD, in addition to...

30 July 2024 3,849 0 View

Ternary in Electrical Engineering?

Dear Research Community I would like to invite Elctrical Engineering specialists to solve problems related to Ternary Algebra or tripple sets I have an algorithm that places in relation three...

28 July 2024 5,771 2 View

Will the catalytic effect of retained austenite happens in steels including RA?

The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...

27 July 2024 8,508 0 View