if yes, then what is the difference between the two binders?
I am scanning CV curves using 3M Na2SO4 electrolyte in Ag/AgCl, Pt mesh and Phos-COF as my positive electrodes, respectively. Every time it gives me straight line at 0. Why this happens?
31 December 2019 3,866 0 View
How we can determine the proper value of current density that i should apply to this system? What is the general procedure to select suitable current density to that system which i mention above....
02 March 2019 9,792 2 View
How we can explain this ...
02 March 2019 7,541 3 View
I am using 3M KOH as electrolyte with Pt counter as counter and Ag/AgCl as reference electrode for my system.with increasing current density why potential is increases? Is this is unusual behavior...
01 February 2019 9,604 4 View
Is its a normal behavior? If not, then any reason, any comments, suggestions will be highly appreciated
31 December 2018 669 6 View
I am using the desired setup for CCD in my work. my question is, what does these value corresponds to how much current in ... A/g?
31 December 2018 5,273 3 View
The graph between number of cycles with respect to specific capacitance
31 December 2018 9,143 0 View
I want to use NCS/CNT as cathode and Carbon fiber paper (CFP) as anode for supercapacitor assembly and i want to widen the potential window. My question is; what is the criteria to take anode...
11 December 2018 7,912 0 View
NiCo2S4 with 6M KOH electrolyte with Ag/AgCl used as reference electrode
08 September 2018 2,658 4 View
I am using 6M KOH electrolyte and tested the behavior of Ni foam without pressure and with pressure. I observed that, with no pressure (without press Ni foam) the current is very high as compared...
03 April 2018 3,849 7 View
I tried four trials of the same Copper Phosphides sample in Alkaline medium ( 0.5M KOH) with Hg/HgO reference electrode and Pt as counter electrode. I used 0.001 V/s scan rate for first three...
10 August 2024 3,629 1 View
I have been using paraffin, but the deposited ZnO still detach from electrode. What is the best binder to modify graphite paste electrode with ZnO nanoparticles?
03 August 2024 4,624 3 View
My screen printed electrode CV is given here. For Nerstean one electron reaction the delta E value should be close to 57 mV and ration of Ic/Ia should be close to 1. I did CV of my screen printed...
30 July 2024 4,671 3 View
We are working on biopolymeric hydrogels. Our system is highly viscous and sticky, and the gel formed are high in strength. We are unable to use pH electrode and pH strip. Please suggest an easy...
30 July 2024 942 2 View
Here, I have used Ag/AgCl as reference electrode and 0.5M KOH.
29 July 2024 4,538 3 View
While I am doing HER, I noticed that nyquist plots of Electrochemical Impedance Spectroscopy (EIS) is not complete. Will it affect for the Linear Sweep Voltametry (LSV) data? However, I can found...
26 July 2024 7,542 4 View
As shown in the figures, there are several abnormal charge/discharge curves.Each of them may have different problems. I am curious why these situations appeared differently?There are a lot of...
24 July 2024 6,930 1 View
I am trying to drop cast 2D Materials on Glassy Carbon Electrode for Cyclic voltametry and EIS purpose. What would be best binders to use?
23 July 2024 5,776 2 View
I have attached the charging curve from the battery tester for review. I need help on what is happening
21 July 2024 6,898 2 View
I want to know that n-doped side of solar cell is connected with positive or negative electrode.
20 July 2024 1,348 2 View
