Iam working on vibrational analysis of laminated composite plate using MATLAB.
https://www.sciencedirect.com/search?qs=vibrational%20analysis%20of%20composite%20plate&show=25&sortBy=relevance
Aniket Suryawanshi use these links
http://extras.springer.com/2009/978-1-4020-9199-5
https://www.springer.com/in/book/9781402091995
do some little change in stiffness matrix and geometric matrix
thanks
Laminated means... are you asking for plate with multiple layers
i have tried modified hummer's method for the synthesis of graphene oxide by adding Graphite powder and NaNO3 in H2SO4 . In this mix KMnO4 was added and diluted with water . this mix was heated...
13 January 2021 9,423 4 View
I have un-replaceable tissues to process for several experimentation such as MS/ WB/ IHC etc. However, I suspect the direct contact of liquid nitrogen to my samples for the duration of few...
18 October 2020 9,375 3 View
I want to determine the stresses for a laminated composite plate under thermo-mechanical load.
24 May 2019 9,180 4 View
I am trying to solve central composite design ANOVA table manually. It has total 30 number of runs which includes 16 factorial runs,8 axial runs and 6 center runs. so, far using regression method...
23 April 2018 2,103 1 View
HepG2 is considered as a model system for various cytotoxicity experiments according to many studies. Won't it produce wrong results if carcinoma cells have been used for such studies as such...
21 August 2017 5,310 7 View
I am looking for a high power LED with a central wavelength of around 488 nm. I know Thorlabs sells one at 490 nm that supplies 216 mW of optical power at 488 nm. However, I need at least 1 W at...
01 June 2017 4,234 3 View
why xrd data of powder materials do not have stable baseline throughout 2theta range(10-90) . Baseline shifts from top to down as angle increases?
18 April 2017 4,844 4 View
for example, in case of 16s rRNA nBLAST results, I have almost 80 similar sequences with % similarity ranging from 99% and going down till 94% ?
16 March 2017 4,772 2 View
I encountered a problem in my project work on heat exchangers where to find heat transfer coefficients on the defined conditions the Reynolds number came to be 1753.8 while the Prandtl number is...
08 March 2017 4,652 3 View
I have found a novel mutation in clotting factor 2 gene in an exon (midway through the exon), however, on checking with mutation tester it is showing that the mutation may result in splice site...
01 March 2017 8,737 3 View
I am making polymer composite by solvent mixing method. When I am trying to add filler solution in polymer solution it quickly get solidified. How to make them then uinform? It doesn't give time...
03 March 2021 7,540 4 View
I am using a 2707 waters HPLC device. When I try to inject a sample, it says missing plate or rack. I changed the needle and calibrated its position but I still get the same problem. I even get...
02 March 2021 1,408 1 View
We have HUVEC bought from Invitrogen. Cat no -C-003-5c. while first plating the cells we have bought the protocol suggests not to centrifuge the cell with media to remove the DMSO. Should we...
02 March 2021 3,713 2 View
Good afternoon, I recently used OmniLog from BIOLOG for my experimentations : I tested the metabolism of different strains on 2 types of plates. I have 16 strains of 3 different groups...
02 March 2021 3,584 1 View
How would define the "good" and "poor" distribution of particles within the matrix. Is there a quantitative solution to assess the distribution of the particles, which then having denotation of...
28 February 2021 7,397 8 View
We have always used the 96 welled plate, the 48 welled plate but apparently there is much evidence on the 24 welled plate and above all its benefits.It states it is the same you would use on ELISA...
28 February 2021 1,149 1 View
Hi, recently I encountered a protocol for plating which was not the usual method I have been practicing (pour LB agar onto plate, allow it to solidify, pipette bacterial suspension onto plate,...
28 February 2021 7,292 3 View
Hello, recently I am having some difficulties with maintaining the cell culture of primary cells isolated from a skin biopsy (normal and malignant). The coating of culture plates with Matrigel (a...
26 February 2021 6,151 2 View
I am facing difficulties in cloning a 1kb gene into a vector (pJIT163). I have my gene on interest (GOI) in pUC57 and want to clone in pJIT163 using SalI and BamHI restriction sites. I am getting...
25 February 2021 3,221 7 View
Hi all, Can cells be reused after I have seed them onto 96 well plates and test them with cell counting kit at OD450 (CCK8) at 12 hours, wash them with PBS x3 and add new media and let them...
24 February 2021 5,072 1 View