Problem facing while doing a Fatigue Analysis?

20 September 2023 0 6K Report

Hello everyone, I'm not able to do fatigue analysis of my model in ANSYS workbench, because I need some values .The material that I selected is ABS High Impact.

I attach a file please check and help me.

Thank you

Badges
Science topic

More Aniket Sandhu's questions See All

What is involved in morphological changes of SEM images of a substance?

In the sem analysis of CaCO3 nanaoparticles, the morphology images showed spherical shaped particles but the proposed morphology for these type of nanoparticles is trigonal. I prepared the...

01 March 2021 1,960 4 View

Which is an ideal solvent to dissolve CaCO3 nanoparticles?

I want to check antibacterial activity of CaCO3 nanoparticles, and I have to make suspension in which they can easily disperse. I have tried DMSO, chloroform, ethanol, saline and DI water, but...

04 November 2020 4,130 3 View

How To Keep A Network Running Even When The Server Is Down?

I was working on MIB server for educational purpose. But since a week I am unable to use the server. It is either restricted or down, I don't know what the problem is. But I want to dock my metal...

02 November 2020 8,775 3 View

What are the suitable conditions to probe sonicate CaCO3 nanoparticle dispersion before doing SEM measuremnts?

Need to know sonication time for SEM measurements of nanoparticles

07 September 2020 4,417 3 View

Conjugation of antibody with oligo?

I want to conjugate my antibody with oligo. I used SMCC approach. But the problem is that i get 3 types of antibody as product. 1 Unlabeled antibody 2 Labelled antibody with single chain of...

03 September 2019 7,075 3 View

How can I apply a thermo-mechanical load in hypermesh?

I want to determine the stresses for a laminated composite plate under thermo-mechanical load.

24 May 2019 9,180 4 View

Can I get MATLAB code for vibrational analysis of composite plate?

Iam working on vibrational analysis of laminated composite plate using MATLAB.

28 October 2018 7,641 3 View

What are the mechanical properties of glass fibers, carbon fibers (only fibers) ?

hello everyone I want the mechanical properties of glass and carbon fibers (only fibers, not the properties of composites)

03 September 2018 3,446 3 View

How we can determine individual sum of squares for independent variables (factors) in the central composite design?

I am trying to solve central composite design ANOVA table manually. It has total 30 number of runs which includes 16 factorial runs,8 axial runs and 6 center runs. so, far using regression method...

23 April 2018 2,103 1 View

What is the difference between Control and Dummy variables? Additionally what are the reasons of Error Term in Regression Model?

Control & Dummy variables: Reasons for Error Term in Regression Model

10 April 2018 5,255 3 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

Is anyone familiar with the cyclic compressive fatigue testing (BS EN 12697 - 25) ?

I would like to get more information on the cyclic compressive fatigue testing (BS EN 12697 - 25) which is typically done for bituminous material in pavement design. Any one can advise on the...

28 February 2021 2,004 3 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View

Complex wave form in ANSYS?

Is there a way to input wave speed in a complex form on ANSYS? The wave speed I need to assign a material is 325(1+0.11i) however I have been unable to do this thus far. Failing that, is there...

27 February 2021 5,969 1 View