a rectangular plate is loaded at center with point load. can i apply failure criteria in ANSYS?
sir i am modelling laminated composite plate... on which i want to apply failure criteria such as Tsai Wu under transverse loading condition.
I am comparing solutions of linear elastic response of a material in Abaqus explicit with inbuilt model and with VUMAT (Linear Elastic) code on single element. I am getting almost same results...
08 September 2019 8,296 2 View
I am doing fatigue damage analysis of composite in Abaqus. How to simulate high number fatigue say 10K or 20K cycles in abaqus, since it is not feasible to simulate each cycle due to high...
04 May 2018 1,026 2 View
I have created .RPT in Abaqus but when I open the file it doesn't contain any proper data and most of the columns have NO VALUE. I would be thankful if anyone can provide the procedure to export...
06 July 2017 1,220 13 View
In research articles term 'normalized stress' or Normalized modulus is frequently used. What is normalized stress or modulus? And what is its significance?
31 December 2016 6,290 0 View
looking for design guidelines of striker mechanism or gas gun mechanism of split hopkinsor pressure bar. what are the parts of launching system and what instrumentation is required?
10 November 2016 8,606 0 View
some study material for FEM of ceramic matrix composites
09 October 2016 2,804 2 View
can anyone suggests procedure to perform FEA of ceramic matrix composites?
09 October 2016 3,560 3 View
how to define orientation of layers and what should be thickness of cylinder?is it equal to thickness of layers? what should be boundary conditions when internal pressure is applied?
04 May 2016 5,222 5 View
plate dimension 100*100mm, material graphite/epoxy, stacking sequence (0/90/0/90/0/90/0) ply thickness=1/7, total thickness of laminate=1mm , applied stress=1MPa, but after solving the problem...
04 May 2016 5,259 5 View
what is the meaning of 95,181,281 in SOLID95, SHELL181 and SHELL281?
04 May 2016 6,850 1 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I am experimenting with cancer and non-cancer cells in a 12-well plate for 4 days with a seeding density 1*10^4/well, however, I noticed that the control group growth rate slows down on D3. Should...
07 August 2024 2,283 2 View
Hi, I have a question about normalizing the MTT OD values for doing the statistical analysis. So, if we have 3 different plates and we call them 3 different replicates, so, first we would...
07 August 2024 8,106 4 View
I have been performing short phagocytosis experiments using 96-round bottom, tissue culture treated, well plates (Falcon, 353077). I culture the cells with the phagocytic cargo for 2-4hrs, wash...
04 August 2024 5,228 4 View
In my study, I intend to infect PBMCs with SARS-CoV-2. After that, I will analyze NK cells by flow cytometry to see if their phenotype changes or if they show degranulation. After the infection, I...
01 August 2024 4,403 4 View
Dear researchers, Today, we found this object in one of the wells of a 96wp culture plate. The plate contained MEC-1 cells and GelTrex. I am quite curious what this is (because it's not cells). Do...
01 August 2024 2,250 2 View
Does anybody know of entomological Journals without page charges that would publish an extensive checklist (Hong Kong Aculeates wasps) covering 350 species (of which more than half are new to Hong...
01 August 2024 6,134 2 View
I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...
29 July 2024 2,032 2 View
Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...
27 July 2024 356 3 View
Hi, Kindly guide me that how many cells of HEC1A & HEC1B Cell lines should I seed for Wound healing assay and which plate type is recommended 6, 12 & 24?. Articles suggested mainly 24...
20 July 2024 4,143 2 View