[SOLVED] Do you have the L. R. Baker's thesis, 'Flexural action of masonry structures under lateral load'?

[SOLVED] I am looking for an old thesis, which was written by L. R. Baker in 1981. I wonder anyone has the softcopy of this thesis paper? Ref: Baker, L. R. (1981). Flexural action of masonry...

07 August 2018 3,343 3 View

Which element type should analyst use for Finite Element Analysis (simulation)?

For any given Finite Element Analysis (simulation) it's essential to define each part of the geometry with one or more elements depending on the types of structures and analysis. As far as I know,...

01 February 2018 1,434 4 View

What is stochastic finite element modelling?

08 September 2017 4,195 1 View

Research paper on numerical modeling of masonry veneer and cavity wall subjected to seismic and wind load?

Can anyone please suggest few research paper which include the numerical modeling of masonry veneer wall and cavity wall under seismic and wind load? Please don't answer if you are not sure about...

02 March 2017 7,975 1 View

Any way to download and activate ABAQUS for personal use?

I tried to download the ABAQUS v6.14 SE from from official website (3DS Academy) by using my school id. However, after downloading when I was installing, it showed that, "File is Corrupt". I check...

02 March 2017 9,953 2 View

In ABAQUS how to model wire mesh of ferrocement?

To model wire mesh of the ferrocement in ABAQUS, may I consider wire mesh same as concrete reinforcement model?

02 March 2017 5,578 6 View

What is the meaning "scale factor for the yield stress" in LS DYNA?

10 November 2015 2,691 1 View

How can I calculate energy dissipation (by porous materials like aluminum foam) from deformed volume?

Due to impact load there is a deformation in specimen and I need to calculate the energy absorbed by the specimen (aluminum foam). I have mass and velocity of the striker, deformed volume of the...

09 October 2015 6,730 4 View

What is the range of strain rate for closed cell aluminum foam where it can show significant strain rate sensitivity?

I want to know the maximum strain rate limit for closed cell aluminum foam, beyond this limit there is no strain rate effects to aluminum foam. That means, on which range of strain rate exhibits...

09 October 2015 3,452 1 View

If I submit one manuscript in two journals together, what is/are the problem(s) actually?

I am confused about one journal that, there is any chance or not to accept my paper. That's why if I want to submit one manuscript in two journals simultaneously, what is/are the problem(s)? And...

05 June 2015 7,025 2 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Arena simulation - how do i model the following model in ARENA (see description) (new to ARENA)?

Hello, I'm fairly new to ARENA and I have the following problem: I have two queues in which, in each queue, a different order type arrives (both having an arrival rate of exponential 10). Order...

02 March 2021 2,431 3 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View

Isolates of Hymenoscyphus fraxineus?

Dear Dr. Cai, my name is Simone Prospero and I work in the team of Phytopathology at the Swiss Federal Institute for Forest Snow and Landscape Research (WSL;...

01 March 2021 1,133 1 View

How to classify strictly upper triangular matrices by similarity?

Let F be a field. Consider U, the set of n times n strictly upper triangular matrices in F. For X, Y in U, we call them similar if there exists some S, which is non-degenerate and upper...

01 March 2021 2,957 8 View

Is CD44 degraded in lysosome together with hyaluronan after CD44 mediated endocytosis of hyaluronic acid?

Also when RHAMM binds hyaluronic acid, they get internalized, will RHAMM also be degraded? Or both CD44 and RHAMM will be transferred back to the cell membrane? Asking for breast cancer cell line...

01 March 2021 8,169 2 View