I want to know about simulation with MAGIC 3D.
Does anyone know about MAGIC 3D?
I want to know the effect of inductor and conductor on microwave.
05 June 2016 1,568 0 View
can any one give me some information about this phenomena?
01 February 2016 5,728 1 View
I want a short pass color filter glass that it's cut off W-L be in 680 or 690nm and one other 800nm one other 890 or 880 nm one other 1000 or 1010 nm are there these color filter glasses?
09 October 2014 1,201 0 View
I want to find a colored filter glass that combined from a low- and high-pass filter to support 780 nm wavelength by 10 or 15 nm accuracy in peak of transition.
08 September 2014 2,053 6 View
To create an optical filter we use some materials as coating for a sublayer. Some of this materials have absorbance and some have reflectance properties. I want to know the influence of the...
06 July 2014 9,092 8 View
What is the difference between a semi-conductor laser and a diode laser?
02 March 2014 6,950 2 View
I want to solve 2D - temperature equation in matlab by FE method in cylindrical system(r z phi) and symmetric about angle PHI. The derivative of temperature to time is zero,but our elements...
02 March 2014 840 7 View
Pumping in diode laser
10 November 2013 8,709 2 View
I’m trying to reproduce the acousto-optic coupling simulation in the paper Frequency–angular resolving LiDAR using chip-scale acousto-optic beam steering. LNOI(lithium niobate on insulator) is...
13 August 2024 9,795 0 View
I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?
11 August 2024 3,115 1 View
I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...
10 August 2024 4,005 2 View
Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...
09 August 2024 7,892 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...
06 August 2024 9,986 2 View
Hi, I know that low molecular weight (MW) molecules generally tend to have higher mobility, while high molecular weight molecules tend to have lower mobility. However, in my experimental...
06 August 2024 1,495 2 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View
I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...
05 August 2024 3,665 0 View