What is the difference between influence of inductor and conductor on microwave?

I want to know the effect of inductor and conductor on microwave.

05 June 2016 1,467 0 View

About diocorton instability in plasma?

can any one give me some information about this phenomena?

01 February 2016 5,619 1 View

Can anyone help me to find a comfortable colored filter glass?

I want to find a colored filter glass that combined from a low- and high-pass filter to support 780 nm wavelength by 10 or 15 nm accuracy in peak of transition.

08 September 2014 1,951 6 View

Does anyone have knowledge on the optical properties of filters?

06 July 2014 8,984 8 View

What is the difference between a semi-conductor laser and a diode laser?

What is the difference between a semi-conductor laser and a diode laser?

02 March 2014 6,844 2 View

Can anyone help me to solve the 2D - temperature equation by FEM (finite element method) in MATLAB?

I want to solve 2D - temperature equation in matlab by FE method in cylindrical system(r z phi) and symmetric about angle PHI. The derivative of temperature to time is zero,but our elements...

02 March 2014 702 7 View

Can anyone help me with simulation?

I want to know about simulation with MAGIC 3D.

01 February 2014 4,006 1 View

How can we increase pumping in the laser (LD)? In other words, can we set the amount of carriers in the active layer arbitrarily?

Pumping in diode laser

10 November 2013 8,573 2 View

What thickness need for ITO to use as conductive layer?

I want to do RF sputtering of ITO on glass substrate using magnetron sputtering. what thickness do i need to make it good conductive layer to use it for PSC. Moreover, whats about thickness of...

01 March 2021 395 3 View

Glass fiber content in a gypsum board ?

Any idea on how to get the volumic ratio of glass fiber in a gypsum board ? Thank you for your help !

01 March 2021 2,501 3 View

Concrete compressive strength databases?

I am looking for datasets similar to this one: http://archive.ics.uci.edu/ml/datasets/Concrete+Compressive+Strength I am looking for concretes with different types of aggregates (Recycled,...

27 February 2021 6,801 3 View

How to properly calculate the fluid solid heat transfer between polypropylene matrix and glass fiber in a porous medium?

I'm building a cfx model of thermoplastic pultrusion process on ansys and i have a doubt on how is the proper way to set this parameter in a porous medium

24 February 2021 1,915 1 View

How to properly calculate Interfacial area density in a porous domain?which are possible value for glass fiber?

I'm doing a cfx simulation of a multiphase flow in pultrusion and i set the Interfacial Area density in the heat exchange of a porous medium in this way IAD=Total fiber lateral surface of fiber...

23 February 2021 6,043 1 View

How can I measure the thickness of thin layers deposited on textured glass susbtrates?

I want to measure the thickness of aluminum oxide and titanium oxide layers deposited on textured glass substates. The layer thicknesses are typically below 100nm.

21 February 2021 5,465 4 View

How can I measure the surface interaction or surface interfacial chemistry between polishing abrasives and upper surface of substrate ?

I am working on polishing abrasives. I need to do few characterizations ? which can provide the on time surface chemistry of substrate with polishing abrasive during optical polishing. I would...

18 February 2021 5,319 3 View

No title

The regenerated cellulose film was prepared by zinc chloride/H2O system. The zinc chloride had been washed away in the regeneration process, and the wet film which was not dried had uniform...

18 February 2021 9,538 1 View

Which is the best silane for making a borosilicate glass surface hydrophobic permanently? and what is the protocol?

Regarding my needs I am looking for a glass coating agent that makes the glass hydrophobic permanently

09 February 2021 3,924 5 View

Is 60%/40% a typical fiber-matrix ratio in vehicle GFRP/CFRP composites?

Quick question I couldn't easily find a definite answer, so I hope someone here could help. I've been looking for information about the ratio (by weight) of glass or carbon fiber to epoxy matrix...

04 February 2021 740 1 View