Can anyone help me in how to proceed with new approach towards floor deck slab design?

More Mandar Pandurang Ganbavale's questions See All

What is the difference between Generic Wall and Masonry Wall in Revit?

I am using Revit 2019.

08 September 2018 5,323 0 View

What are the steps involved while meshing reinforced concrete slab?

I am analyzing reinforced concrete slab with an element size of 4 mm. Attaching image with close view of mixed mesh. I have used standard 3D truss elements to mesh with, according to the tutorials...

01 February 2015 2,256 3 View

How can I handle Interaction module in Abaqus?

Hello all respected researchers, I am working on abaqus, and would like to know how to handle this Interaction module in abaqus while modelling RCC rectangular slab to analyse it at very basic...

01 February 2015 3,923 2 View

How can one resolve this error while analysing RCC slab in ABAQUS?

Hello all, I am trying to analyse RCC slab under UDL using FEA tool ABAQUS 6.13.1. I am getting the following error 9 nodes on an embedded element do not lie in any host element. Check...

01 February 2015 6,062 3 View

How can one assign failure properties of RCC slab in abaqus while analysis?

Hello all, I am analyzing Rectangular RCC slab. While doing the analysis I have managed to assign elastic properties of steel and concrete but couldn't manage to assign plastic or failure...

01 February 2015 9,039 3 View

What is this error in abaqus while meshing? How do I resolve this?

Hello all researchers, I am analysing RCC slab with 8 mm diameter steel bars embeded in concrete. The slab is two-way. While meshing it I am getting errors like the ones shown in the image...

01 February 2015 3,179 5 View

What is this error in abaqus?

Detected lock file Job-1.lck. Please confirm that no other applications are attempting to write to the output database associated with this job before removing the lock file and...

31 December 2014 8,572 14 View

Can anyone help me in Do's and Dont's while applying for PhD in top ranked universities?

Dear researchers, I am pursuing my masters degree in Structural engineering and after this I would like to pursue PhD degree in one of the best universities all over the world. I would like to...

31 December 2014 3,622 3 View

What are the general, mechanical and thermal properties of RCC?

Hello all, I am working on ABAQUS for FEA. I have drawn sketch of simple beam. Now, I want to assign the material properties. Reinforced cement concrete. Can anyone provide me detailed properties...

31 December 2014 1,991 3 View

Can anyone provide me list of well reputed journals (top 10 in terms of impact factor) in civil engineering?

I have worked on structural optimization using MATLAB. Now I want to publish in an International Journal. I thought Computers and structures first. But, I would like to know which would be a...

11 December 2014 3,671 24 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

How to learn more about SPSS and its Application?

I would like to learn more about SPSS and Its application especially in regards to data analysis. Please suggest me how I can learn more about it. Thank you so much.

11 August 2024 9,101 4 View

Can I base on reverse DNA sequences to perform alignment, convert to amino acids and GenBank submission?

I have reverse sequences (AB1 format), can I base on reverse DNA sequences to perform nucleotide alignment, convert nucleotides to amino acids and deposit the sequence in GenBank database?

11 August 2024 5,138 1 View

Baseline drift in HPLC? What causes this?

Hello, Why do i see this baseline drift when i compare my blank (black) to the sample (blue)? Any suggestions as to why this happened? Thank you!

11 August 2024 3,770 4 View

Text-Communication from the M1 Hand Area using BCI—and then there is Elon Musk?

Willett, Shenoy et al. (2021) have developed a brain computer interface (BCI) that used neural signal collected from the hand area of the motor cortex (area M1) of a paralyzed patient. The...

10 August 2024 7,180 0 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Has anyone applied Python in the field of textile engineering for data analysis, automation, or smart textiles?

I'm currently exploring the application of Python in textile engineering, specifically in areas like data analysis, process automation, and the development of smart textiles. I'm interested in...

10 August 2024 7,429 2 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How can I use the cif data obtained from rietveld refinement extracted via gsas2, for microstructural analysis using ETEX software?

09 August 2024 7,718 0 View

Efe Greg

Your design considerations would essentially inform the type of approach to use. The easiest way would be to compare information obtained from an FEA study of a comparable slab design to that of your design and make improvements as required. This is important from the safety standpoint.

Hussam Ali Mohammed

Interesting