Is it possible to entrain a particle(s) into a gap/crack/cavity within Ansys Fluent?

I am trying to simulate the entrainment of a discrete phase particle in Ansys Fluent. Essentially, the particles would enter a pipe containing water, and flow into a hole in the pipe, and become...

13 January 2021 4,789 3 View

Is it possible to model a pressure-activated sealant in Ansys fluent?

I am trying to figure out how you'd model a pressure-activated sealant within Ansys fluent. This would be able to seal over a small crack, represented by a pressure differential, on the inside of...

12 January 2021 2,504 3 View

Would a non-Newtonian fluid be the best way to approximate the flow of large particles in Ansys which can plug a leak?

I am trying to model the sealing of a leaking water pipe within Ansys fluent, using the insertion of a stream of particles into the pipe, which would be forced into the gap by the pressure...

12 January 2021 9,509 0 View

Culturing Breast Cancer Cells changed color when sprayed with Bleach?

Hey Guys, I'm culturing cancerous breast tissue cells in vitro. Today I took the 24 well plate out of the incubator, and, being done with the cells, I sprayed bleach in all 24 wells. Instantly,...

23 April 2017 6,222 1 View

Do I need to keep cell lines under selection after they have grown out post-transduction?

After selection, when cells have grown out in the presence of my antibiotic, do I keep them under selection with antibiotic indefinitely, or take them off?

29 March 2015 7,715 4 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

What kind of fluid could I use for a pitfall trap that also does not invalidate molecular testing?

Hi, I want to start testing pitfall trap to obtain ants samples, but I need to conduct molecular analysis on those insects. So, what kind of fluid can I use? Ethanol expires too early and I need...

03 March 2021 5,978 5 View

No title

02 March 2021 3,060 3 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View

New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before?

Question to you and THEM, the New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before? There appears to be a core problem for...

02 March 2021 3,024 2 View