I am planning to model and analyze the warm deep drawing using Abaqus software. If anybody has the tutorial or an idea related to the warm deep drawing please help me to do this analysis.
Dear Bala
Try Abaqus documentation. Below address contains a solved 2D deep drawing process. You can modify it for thermo-mechanical analysis:
Getting Started with Abaqus: Interactive Edition
12.6 Abaqus/Standard 2-D example: forming a channel
try to do the exemples in this book .
if you had any problems i can send example cae
Please share me the best answer might you trust...
Regards…
I want to do the warm deep drawing using Abaqus software. Since I have some idea about the cold deep drawing for simulation.If anybody have idea related to the warm deep drawing please share with...
11 December 2016 3,531 0 View
I have seen ductile fracture criterion(Frendenthal ,ckcroft and Latham ,Brozzo ,Ohet al) in some journals.I could not able to understand how to calculate material constants (c).If anybody have...
11 December 2016 5,671 2 View
I have seen some journals in that the ductile fracture criterion (Frendenthal ,cockcroft and Latham ,Brozzo ,Ohet al)were used. I could not understand how the material constants (c) determined. If...
11 December 2016 1,808 3 View
I am doing the research work in sheet metal forming (deep drawing). So please anyone help me to do the deep drawing process in ANSYS software.If you have any tutorial please send it to my...
06 July 2016 5,681 1 View
I am doing my research work in micro deep drawing ,I want to know the Voronoi cell FEM and how to implement the concept in Abaqus software for finding the size effect. Thank you, M.Subramanian
06 July 2016 3,847 2 View
I have sent a research paper to a journal. In that paper ,I selected the punch diameter of 5 mm. The reviewer comment is as follows: "The punch diameter of the forming parts in this paper is 5mm,...
05 June 2016 6,773 0 View
Can anyone give ideas or tutorial for warm deep drawing process by using Abaqus software.How to give the temperature and heat transfer co-efficient in the software. With regards, M.Subramanian
05 June 2016 4,314 1 View
I am using the software Abaqus for micro deep drawing , I sent my paper to the journal for publication, but I received the comment from reviewer is " FEM simulation is not suitable for micro deep...
05 June 2016 3,079 5 View
I have simulated 2D deep drawing process using Abaqus software. I got the result for deformed cup output.In the output contour result, the maximum value of PEEQ is indicated in the Die corner...
07 August 2015 5,423 4 View
I have some idea about the 2D simulation of deep drawing by referring the Abaqus user's manual.Since I want to simulate the 2D or 3D simulation of deep drawing in warm conditions.If anybody have...
05 June 2015 4,499 0 View
I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?
11 August 2024 3,115 1 View
I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...
10 August 2024 4,005 2 View
Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...
09 August 2024 7,892 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...
08 August 2024 4,831 4 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
Let's say we have a standard, regular hexagonal honeycomb with a 3-arm primitive unit cell (something like the figure attached; the figure is only representative and not drawn to scale). The...
07 August 2024 1,937 1 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,028 0 View
Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...
06 August 2024 9,986 2 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View